Become a Site Supporter and Never see Ads again!

Author Topic: TASCAM DR-100mkIII NEW Unreleased Recorder  (Read 114903 times)

0 Members and 1 Guest are viewing this topic.

Offline spyder9

  • Trade Count: (82)
  • Needs to get out more...
  • *****
  • Posts: 13195
  • Gender: Male
  • "Are you Zman?"
    • My Archived shows
Re: TASCAM DR-100mkIII NEW Unreleased Recorder
« Reply #165 on: July 26, 2017, 12:04:40 PM »
Shootout:  Tascam DR-100 mkiii vs Marantz PMD661 (Oade warm mod)

http://taperssection.com/index.php?topic=183001.msg2235427#msg2235427

Offline SIRMick

  • Trade Count: (0)
  • Taperssection Newbie
  • *
  • Posts: 24
  • Gender: Male
Re: TASCAM DR-100mkIII NEW Unreleased Recorder
« Reply #166 on: January 18, 2018, 12:59:44 PM »
Hi

I've had one of these for a little while and have been using mics that use a small Jack plug. I've just now bought some AT831B mics. If I connect them via their individual power supplies they work just fine but as I want to use them for stealth recordings I don't want to have to carry 2 power supplies and two one meter long cables.

I've tried to get them to work using these https://www.ebay.co.uk/itm/3-pin-XLR-Male-to-3-pin-Mini-XLR-Male-Mic-adapter/162475570222?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649 to connect them direct to the xlr inputs and turned on phantom power but so far I can't get them to run.  I have tried several options for I/O.

Any help offered will be much appreciated as this is very frustrating.


Offline beatkilla

  • Trade Count: (70)
  • Needs to get out more...
  • *****
  • Posts: 2104
  • Gender: Male
Re: TASCAM DR-100mkIII NEW Unreleased Recorder
« Reply #167 on: January 18, 2018, 01:10:40 PM »
Hi

I've had one of these for a little while and have been using mics that use a small Jack plug. I've just now bought some AT831B mics. If I connect them via their individual power supplies they work just fine but as I want to use them for stealth recordings I don't want to have to carry 2 power supplies and two one meter long cables.

I've tried to get them to work using these https://www.ebay.co.uk/itm/3-pin-XLR-Male-to-3-pin-Mini-XLR-Male-Mic-adapter/162475570222?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649 to connect them direct to the xlr inputs and turned on phantom power but so far I can't get them to run.  I have tried several options for I/O.

Any help offered will be much appreciated as this is very frustrating.

You can have a cable maker here reterminate them and if needed 4.7k mod.

But i think you may have fried them already if you applied p48 to them .Hopefully not the case.

Offline SIRMick

  • Trade Count: (0)
  • Taperssection Newbie
  • *
  • Posts: 24
  • Gender: Male
Re: TASCAM DR-100mkIII NEW Unreleased Recorder
« Reply #168 on: January 19, 2018, 03:17:43 AM »
Well I just tried again with the metal convertors and it's working fine.  Very strange.

BTW: Can you explain to me by a 4.7k mod?

Thanks

Offline kuba e

  • Trade Count: (1)
  • Taperssection Member
  • ***
  • Posts: 492
  • Gender: Male
Re: TASCAM DR-100mkIII NEW Unreleased Recorder
« Reply #169 on: January 19, 2018, 05:33:52 AM »
Well I just tried again with the metal convertors and it's working fine.  Very strange.
Do not connect mics straight to p48. You will destroy them.

If you want to use them with p48, you need phantom adapter. These mics are three wires. One wire is for power, second is for audio signal, third is ground. Phantom adapter steps down p48 to small voltage and divide this voltage between wires. This is the right way how to power these mics. The second purposed of phantom adapter is that it converts mic's unbalanced signal to balanced signal. Then you can use long cables between the adapter and the preamp.

BTW: Can you explain to me by a 4.7k mod?
It is possible to use this mic in two wire configuration with classical battery box (9 V) too. But the mic is not properly powered in this way and you get distorsion on high SPL.
4.7k mod is Chris Church's mod (you put the resistor 4.7k between pin 2, 3). This mod enable you to use the mics in two wire configuration with 9 V battery box for high SPL too.
« Last Edit: January 19, 2018, 05:37:06 AM by kuba e »

Offline SIRMick

  • Trade Count: (0)
  • Taperssection Newbie
  • *
  • Posts: 24
  • Gender: Male
Re: TASCAM DR-100mkIII NEW Unreleased Recorder
« Reply #170 on: January 19, 2018, 06:05:20 AM »
Do not connect mics straight to p48. You will destroy them.

If you want to use them with p48, you need phantom adapter. These mics are three wires. One wire is for power, second is for audio signal, third is ground. Phantom adapter steps down p48 to small voltage and divide this voltage between wires. This is the right way how to power these mics. The second purposed of phantom adapter is that it converts mic's unbalanced signal to balanced signal. Then you can use long cables between the adapter and the preamp.


I'm sorry but I don't understand all the terminolgy.  What is p48?  Are there any adaptors that you can recommend. Thanks
« Last Edit: January 19, 2018, 06:10:57 AM by SIRMick »

Offline kuba e

  • Trade Count: (1)
  • Taperssection Member
  • ***
  • Posts: 492
  • Gender: Male
Re: TASCAM DR-100mkIII NEW Unreleased Recorder
« Reply #171 on: January 19, 2018, 10:12:27 AM »
p48 mean phantom power 48V. Condenser mics are working with this voltage, and a lot of preamps/recorders provide this voltage. But AT831B is electret mic, it need around 9V. Here is example of phantom power adapter for electret AT mics. I do not know, if it is working with yours. It is better to ask in the forum which adapter is for AT831B. Or better look into the mic documentation.
https://www.amazon.com/Audio-Technica-AT8538-Power-Module/dp/B000ZLX3EY

If you do not want to use phantom adapter, you can use battery box. In this case it is nessesery to ask somebody to make 4.7k mod on your mics and terminate them to stereo jack. Without 4.7mod you will have distorsions in the recordings on loud shows.
https://www.church-audio.com/shop/battery-boxes/ugly-battery-box/

Edit:
Maybe this is designed for your mics:
https://eu.audio-technica.com/AT8531
« Last Edit: January 19, 2018, 10:20:51 AM by kuba e »

Offline SIRMick

  • Trade Count: (0)
  • Taperssection Newbie
  • *
  • Posts: 24
  • Gender: Male
Re: TASCAM DR-100mkIII NEW Unreleased Recorder
« Reply #172 on: January 19, 2018, 10:49:27 AM »
p48 mean phantom power 48V. Condenser mics are working with this voltage, and a lot of preamps/recorders provide this voltage. But AT831B is electret mic, it need around 9V. Here is example of phantom power adapter for electret AT mics. I do not know, if it is working with yours. It is better to ask in the forum which adapter is for AT831B. Or better look into the mic documentation.
https://www.amazon.com/Audio-Technica-AT8538-Power-Module/dp/B000ZLX3EY

If you do not want to use phantom adapter, you can use battery box. In this case it is nessesery to ask somebody to make 4.7k mod on your mics and terminate them to stereo jack. Without 4.7mod you will have distorsions in the recordings on loud shows.
https://www.church-audio.com/shop/battery-boxes/ugly-battery-box/

Edit:
Maybe this is designed for your mics:
https://eu.audio-technica.com/AT8531

Thanks

I already have two AT8531, they came with the mics but I want to try and avoid having to use them because of the extra weight to carry plus the two leads extra leads.  I will take a look around and see what adaptors are available in Europe as I live in London.

Offline kuba e

  • Trade Count: (1)
  • Taperssection Member
  • ***
  • Posts: 492
  • Gender: Male
Re: TASCAM DR-100mkIII NEW Unreleased Recorder
« Reply #173 on: January 19, 2018, 01:32:59 PM »
Yes, i understand. I think the best way is go for Chris Church battery box and  Y cable with 4.7k mod. Y cable should have 2 mini xlr inputs (for your mics) and output one mini stereo jack (for battery box). Then you will connect - Mics -> Y cable with 4.7 mod -> Battery box -> Ext in (Tascam). You can buy second Y cable without 4.7k mod for recording quiet acoustic shows, then you will use - Mics -> Y cable without 4.7 mod -> Battery box -> Ext in (tascam)

There are more info in the forum e.g. here
http://taperssection.com/index.php?topic=108196.0
or google this: 4.7 mod  site:taperssection.com

« Last Edit: January 19, 2018, 01:47:22 PM by kuba e »

Offline SIRMick

  • Trade Count: (0)
  • Taperssection Newbie
  • *
  • Posts: 24
  • Gender: Male
Re: TASCAM DR-100mkIII NEW Unreleased Recorder
« Reply #174 on: January 19, 2018, 07:25:56 PM »
Yes, i understand. I think the best way is go for Chris Church battery box and  Y cable with 4.7k mod. Y cable should have 2 mini xlr inputs (for your mics) and output one mini stereo jack (for battery box). Then you will connect - Mics -> Y cable with 4.7 mod -> Battery box -> Ext in (Tascam). You can buy second Y cable without 4.7k mod for recording quiet acoustic shows, then you will use - Mics -> Y cable without 4.7 mod -> Battery box -> Ext in (tascam)

There are more info in the forum e.g. here
http://taperssection.com/index.php?topic=108196.0
or google this: 4.7 mod  site:taperssection.com

Thanks for your suggestions but I really want to avoid extra leads. A simple plugin phantom power adaptor seems to suit my needs better.

Offline fanofjam

  • Trade Count: (4)
  • Taperssection Member
  • ***
  • Posts: 507
Re: TASCAM DR-100mkIII NEW Unreleased Recorder
« Reply #175 on: January 21, 2018, 07:20:30 AM »
Yes, i understand. I think the best way is go for Chris Church battery box and  Y cable with 4.7k mod. Y cable should have 2 mini xlr inputs (for your mics) and output one mini stereo jack (for battery box). Then you will connect - Mics -> Y cable with 4.7 mod -> Battery box -> Ext in (Tascam). You can buy second Y cable without 4.7k mod for recording quiet acoustic shows, then you will use - Mics -> Y cable without 4.7 mod -> Battery box -> Ext in (tascam)

There are more info in the forum e.g. here
http://taperssection.com/index.php?topic=108196.0
or google this: 4.7 mod  site:taperssection.com

Thanks for your suggestions but I really want to avoid extra leads. A simple plugin phantom power adaptor seems to suit my needs better.

Because of the gear you've bought, you are now trying to fit a round peg into a square hole.  Unfortunately, while the adapter you're asking for is available, in my opinion that wouldn't be a very good option.  See the last paragraph for details.

First of all, I agree with the other responses that you should buy a two wire battery box.   

Most stereo microphones that use 9V power, also known as Plug In Power (PIP), terminate in a single 3.5mm stereo connector.  If your mics were terminated similarly, you could use the Ext In connector on your DR100mkIII to power your mics.

However, since you have two mono microphones, you cannot connect your mics to the DR100mkIII, so I agree with the others that a two wire battery box is your best answer.  They are tiny. 

You also need the 4.7k mod if you'll be recording loud music...without this mod your mics are going to distort at high volumes.  This is a very simple mod.

OK, so if you insist on the phantom power adapters, this is what you need to buy...

http://naiant.com/studio-electronics-products/inline-devices/pfa-phantom-power-adaptor/

I'm going to be honest though that this would be a poor decision compared to the battery box.  Read the reviews of the DR100mkIII from users that operate the DR100mkIII with phantom power turned on.  Phantom decreases battery run-time on the DR100mkIII significantly.  In my opinion, you'd be solving one problem and giving yourself another. 

Battery boxes are very small compared the size of the DR100mkIII.

Finally, it's unfortunate that you've probably purchased the DR100mkIII because you mistakenly thought that you needed a recorder with two XLR connectors in order to connect your mics, but since you're a stealth taper, I would consider selling the DR100mkIII and buying a handheld recorder...and again use the battery box solution recommended above.
« Last Edit: January 21, 2018, 08:11:34 AM by fanofjam »

Offline SIRMick

  • Trade Count: (0)
  • Taperssection Newbie
  • *
  • Posts: 24
  • Gender: Male
Re: TASCAM DR-100mkIII NEW Unreleased Recorder
« Reply #176 on: January 21, 2018, 07:38:04 AM »
Yes, i understand. I think the best way is go for Chris Church battery box and  Y cable with 4.7k mod. Y cable should have 2 mini xlr inputs (for your mics) and output one mini stereo jack (for battery box). Then you will connect - Mics -> Y cable with 4.7 mod -> Battery box -> Ext in (Tascam). You can buy second Y cable without 4.7k mod for recording quiet acoustic shows, then you will use - Mics -> Y cable without 4.7 mod -> Battery box -> Ext in (tascam)

There are more info in the forum e.g. here
http://taperssection.com/index.php?topic=108196.0
or google this: 4.7 mod  site:taperssection.com

Thanks for your suggestions but I really want to avoid extra leads. A simple plugin phantom power adaptor seems to suit my needs better.

Since you said you're trying to stealth record, if I was in your position I would sell the DR100mkIII and buy a smaller handheld recorder.  And rather than using PIP from the recorder, buy yourself a 9V battery box to power your mics.  They are tiny, inexpensive and fairly commonplace. 

Church Audio sells several battery box designs that are popular on taperssection and are less than the size of a 9V battery.

The basic problem is that your recorder is incompatible with your microphones, so you're trying to fit a square peg into a round hole and there simply are very few options available for the adapter you're looking for.  Mic's that are designed to be powered with a 9V power source just aren't compatible with a recorder that supplies 48V phantom.  However, if you insist on keeping the DR100mkIII, the product that you need is available in the link below.  As far as I know, Naiant is the only source of this type of adapter.

http://naiant.com/studio-electronics-products/inline-devices/pfa-phantom-power-adaptor/

A third option which has not been suggested is to purchase a recorder that supplies 'plug in power' (PIP) directly to your mics from the 3.5mm mic in connector jack.  However, the problem with this option is that most of these recorders underpower the mics...while the mics may work they usually don't get enough power to handle the high Sound Pressure Levels (SPL) at a loud live music concert, so underpowered mics will distort when the sound gets loud.  Some people have reported good results using a few handheld recorders that apparently put a slightly higher voltage through their 'mic in' jack than other manufacturers.  I would caution you to do plenty of research though...you should assume that a recorder with PIP will NOT provide enough power to your mics to record loud music concerts.



I do have a Sony PCM-M10 but what drew me to the Tascam was the fact that I can record at 24/192.  I know that might sound a little extreme but....

I have used the Tascam with CA14s  and the Church Battery box which I still have.

The AT831b can be run on batteries or phantom power, all I want to do is find the right adaptor for my purposes, i.e. one that doesn't involve in using addition leads.  Do you consider that either of these would be suitable https://www.thomann.de/gb/audix_aps_910.htm or https://www.thomann.de/ie/superlux_ps_418_s.htm?ref=search_rslt_phantom+opower+adaptor_315064_15.

Thanks

Offline fanofjam

  • Trade Count: (4)
  • Taperssection Member
  • ***
  • Posts: 507
Re: TASCAM DR-100mkIII NEW Unreleased Recorder
« Reply #177 on: January 21, 2018, 08:31:54 AM »
Yes, i understand. I think the best way is go for Chris Church battery box and  Y cable with 4.7k mod. Y cable should have 2 mini xlr inputs (for your mics) and output one mini stereo jack (for battery box). Then you will connect - Mics -> Y cable with 4.7 mod -> Battery box -> Ext in (Tascam). You can buy second Y cable without 4.7k mod for recording quiet acoustic shows, then you will use - Mics -> Y cable without 4.7 mod -> Battery box -> Ext in (tascam)

There are more info in the forum e.g. here
http://taperssection.com/index.php?topic=108196.0
or google this: 4.7 mod  site:taperssection.com

Thanks for your suggestions but I really want to avoid extra leads. A simple plugin phantom power adaptor seems to suit my needs better.

Since you said you're trying to stealth record, if I was in your position I would sell the DR100mkIII and buy a smaller handheld recorder.  And rather than using PIP from the recorder, buy yourself a 9V battery box to power your mics.  They are tiny, inexpensive and fairly commonplace. 

Church Audio sells several battery box designs that are popular on taperssection and are less than the size of a 9V battery.

The basic problem is that your recorder is incompatible with your microphones, so you're trying to fit a square peg into a round hole and there simply are very few options available for the adapter you're looking for.  Mic's that are designed to be powered with a 9V power source just aren't compatible with a recorder that supplies 48V phantom.  However, if you insist on keeping the DR100mkIII, the product that you need is available in the link below.  As far as I know, Naiant is the only source of this type of adapter.

http://naiant.com/studio-electronics-products/inline-devices/pfa-phantom-power-adaptor/

A third option which has not been suggested is to purchase a recorder that supplies 'plug in power' (PIP) directly to your mics from the 3.5mm mic in connector jack.  However, the problem with this option is that most of these recorders underpower the mics...while the mics may work they usually don't get enough power to handle the high Sound Pressure Levels (SPL) at a loud live music concert, so underpowered mics will distort when the sound gets loud.  Some people have reported good results using a few handheld recorders that apparently put a slightly higher voltage through their 'mic in' jack than other manufacturers.  I would caution you to do plenty of research though...you should assume that a recorder with PIP will NOT provide enough power to your mics to record loud music concerts.



I do have a Sony PCM-M10 but what drew me to the Tascam was the fact that I can record at 24/192.  I know that might sound a little extreme but....

I have used the Tascam with CA14s  and the Church Battery box which I still have.

The AT831b can be run on batteries or phantom power, all I want to do is find the right adaptor for my purposes, i.e. one that doesn't involve in using addition leads.  Do you consider that either of these would be suitable https://www.thomann.de/gb/audix_aps_910.htm or https://www.thomann.de/ie/superlux_ps_418_s.htm?ref=search_rslt_phantom+opower+adaptor_315064_15.

Thanks

The Audix adapters don't provide any information except that they work with electret mics... I have a pair of something similar that work with my PIP mics, so they might work for your situation.  I'd try this first.  The Superlux product seems to be specifically designed for the Superlux mics.  Without additional specs, not sure.

Offline kuba e

  • Trade Count: (1)
  • Taperssection Member
  • ***
  • Posts: 492
  • Gender: Male
Re: TASCAM DR-100mkIII NEW Unreleased Recorder
« Reply #178 on: January 21, 2018, 08:58:59 AM »
I will reply in your new post so as not to disturb the talk about the tascam dr100.
(http://taperssection.com/index.php?topic=185079.0)


Offline capnhook

  • All your llamas are belong to us....
  • Site Supporter
  • Trade Count: (20)
  • Needs to get out more...
  • *
  • Posts: 4843
  • All your llamas are belong to us....
Re: TASCAM DR-100mkIII NEW Unreleased Recorder
« Reply #179 on: January 21, 2018, 09:35:47 AM »

I do have a Sony PCM-M10 but what drew me to the Tascam was the fact that I can record at 24/192.  I know that might sound a little extreme but....


There's your problem....you ARE sounding a bit extreme.

Go 24/48 or 24/44.1

Don't go near the 192 kHz kool-aid....it's just marketing fluff.

 
Proud member of the reality-based community

BSCS-L->JB-mod [NAK CM-300 (CP-3) and/or (CP-1)]->LSD2->CA CAFS-Omni->Sony ECM-907**Apogee MiniMe Rev. C->CA Ugly II->**Edirol OCM R-44->Tascam DR-22WL->Sony TCD-D8


"Don't ever take an all or nothing attitude when it comes to making a difference
and being beautiful and making the world a beautiful place through your actions.
Every little bit is registered.  Every little bit.  So be as beautiful as you can as often as you can"

"It'll never be over, 'till we learn."
 
"My dream is to get a bus and get the band and just go coast to coast. Just about everything else except music, is anti-musical.  That's it.  Music's the thing." - Jeb Puryear

 

RSS | Mobile
Page created in 0.131 seconds with 44 queries.
© 2002-2024 Taperssection.com
Powered by SMF