Taperssection.com

Gear / Technical Help => Cables => Topic started by: tbone65 on November 01, 2018, 11:17:04 PM

Title: power cable for mix pre 3
Post by: tbone65 on November 01, 2018, 11:17:04 PM
im looking for anyone who can help build a special cable.want to power up mix pre 3 .want to take AA sled drill a whole and  solder a cable to the coils or contacts. then terminate the other side of the cable(foot long) to a usb charger plug.   any one able to help build this please contact me off this listing.direct emails to todd1965@verizon.net thank you. tired of this bullshit with sound devices.need to take solid action.
Title: Re: power cable for mix pre 3
Post by: Gordon on November 02, 2018, 08:38:07 AM
tired of this bullshit with sound devices.need to take solid action.


I and 99% of others have had 0 issues with usb battery's.  you also have the L mount option and the dummy aa sled.
Title: Re: power cable for mix pre 3
Post by: dynamicalories on November 02, 2018, 11:31:00 AM
Likewise, I haven't even bothered putting AA's in my MixPre-6. Just using a USB-C battery and cable.
Title: Re: power cable for mix pre 3
Post by: morst on November 02, 2018, 04:07:15 PM

im looking for anyone who can help build a special cable.want to power up mix pre 3 .want to take AA sled drill a whole and  solder a cable to the coils or contacts. then terminate the other side of the cable(foot long) to a usb charger plug.   any one able to help build this please contact me off this listing.direct emails to todd1965@verizon.net thank you. tired of this bullshit with sound devices.need to take solid action.


Are you sure that 5 volts from USB power will be sufficient to duplicate the 6 volts you get with 4 AA's?
The math indicates that it might be like running off a set of AA cells which are down to 1.25 v each, which is past the point I would start a recording, and might not be adequate for "high power" mode on the MP3?


I'd be curious to know how this works, but I'm skeptical overall.


Physically, it's a simple mod: drill a hole in the AA sled, and bust up a USB-A or USB-C cable and find the right wires and solder (or clip?) them onto the proper polarity connectors.
Title: Re: power cable for mix pre 3
Post by: tbone65 on November 03, 2018, 01:08:28 AM
well some of you dont understand. yes 5 volts will power up a mix pre 3.just fine.im not using the AA batteries just the sled to make a contact point for power. the reg usb c  connnection just sucks. it could easily get pulled out during recording.
Title: Re: power cable for mix pre 3
Post by: morst on November 03, 2018, 02:10:10 PM
well some of you dont understand. yes 5 volts will power up a mix pre 3.just fine.

Oh, you've tried it?

5 volts from a normal USB-A pack will not allow for full power mode which is needed for use of bluetooth, or external keyboard. I guess the 3 only has two preamp channels, though...

Title: Re: power cable for mix pre 3
Post by: spyder9 on November 15, 2018, 03:54:27 PM
Todd,

Just buy one of these and your prayers will be answered.  I run my Mixpre-6 with either a DVD battery or Tekkeon battery with this thing.  Way too easy!

https://www.bhphotovideo.com/c/product/1366733-REG/cable_techniques_mx_powersled_powersled_for_sound_devices.html/?ap=y&gclid=EAIaIQobChMIlN-0-aPX3gIV5ZJbCh2zBwoOEAQYASABEgKO7_D_BwE&smp=Y

Title: Re: power cable for mix pre 3
Post by: rippleish20 on November 15, 2018, 04:07:09 PM
USB is 5 volts. When you are powering a Mixpre-3/6 via USB-c it's 5 volts! The issue is the amperage, not the voltage. The Mixpre needs 7.5 watts for full operation - 5 volts X 1.5 amps. The issue with USB-A based batteries is because the USB cable standards set a maximum of .9 amps for a USB-A to USB-C cable) 5 volts x .9 amps - 4.5 watts (yes, some cables ignore the standards)