Become a Site Supporter and Never see Ads again!

Author Topic: 3wire batt bocx for AT943  (Read 32630 times)

0 Members and 1 Guest are viewing this topic.

Offline Chaosu

  • Trade Count: (0)
  • Taperssection Regular
  • **
  • Posts: 72
Re: 3wire batt bocx for AT943
« Reply #75 on: April 17, 2009, 04:09:55 PM »
I finally found someone who can build a bb for me for reasonable amount of money, out of presented schemes he picked this one

I would like to ask if all those values seems ok for AT853 type of mics (SP-CMC-4). I am basically not going to use bass cut but maybe in future... I am also satisfied with these mics so not planning any upgrade (especially if I'll finally have higher SPL handling). Any corrections/ideas welcome. This is meant to be 3 wire bb I hope.

Offline Chaosu

  • Trade Count: (0)
  • Taperssection Regular
  • **
  • Posts: 72
Re: 3wire batt bocx for AT943
« Reply #76 on: April 17, 2009, 06:13:06 PM »
Fuck! Luckily I made that question.... how about this one then?
http://www.gcogger.dsl.pipex.com/stuff/at943_3w_bb.gif
No bass cut but I don't need that anyway.

Offline Sunday Driver

  • Trade Count: (6)
  • Taperssection Member
  • ***
  • Posts: 312
  • Gender: Male
Re: 3wire batt bocx for AT943
« Reply #77 on: April 18, 2009, 01:39:12 PM »
Fuck! Luckily I made that question.... how about this one then?
http://www.gcogger.dsl.pipex.com/stuff/at943_3w_bb.gif
No bass cut but I don't need that anyway.

Yes, that is the proper schematic to use for your application.
You either record it or it's gone forever.
My Tapes

Offline Chaosu

  • Trade Count: (0)
  • Taperssection Regular
  • **
  • Posts: 72
Re: 3wire batt bocx for AT943
« Reply #78 on: May 05, 2009, 07:39:38 PM »
Fuck! Luckily I made that question.... how about this one then?
http://www.gcogger.dsl.pipex.com/stuff/at943_3w_bb.gif
No bass cut but I don't need that anyway.

Yes, that is the proper schematic to use for your application.
I just picked up my battery box. Output is mono. I didn't noticed that earlier and it was made according to schematic.

Offline Chaosu

  • Trade Count: (0)
  • Taperssection Regular
  • **
  • Posts: 72
Re: 3wire batt bocx for AT943
« Reply #79 on: May 15, 2009, 06:44:11 AM »
I was just told that no 3 wire battery box can be made for single stereo input. Is this true?

Offline Neilyboy

  • Trade Count: (14)
  • Taperssection Member
  • ***
  • Posts: 917
  • Gender: Male
Re: 3wire batt bocx for AT943
« Reply #80 on: May 18, 2009, 05:16:06 PM »
the schematic you posted was only single channel. you just need to 'double' the schematic.
http://www.gcogger.dsl.pipex.com/stuff/at943_3w_bb.gif

just my $0.02 may be wrong but from all other bb plans I have seen its just a matter of mirroring the schematic.

/edit.. see "graemecogger" first post.. 'Obviously this needs to be duplicated for the 2 channels.'

so if whoever built this for you just built it exactly the the schematic then yes all you will have is mono. you will need to mirror it to get your second channel.

Neil
« Last Edit: May 18, 2009, 05:22:23 PM by Neilyboy »
Mic's: AKG C214's, Line Audio CM3, AT4041SP, AT853 (C, SC, O), AT943 (C, H)
Pre's: Sound Devices MixPre 2
Rec's: Sony PCM-M10, Edirol R-44, Tascam DR60D MKii, Tascam DR70D x 2

 

RSS | Mobile
Page created in 0.069 seconds with 34 queries.
© 2002-2024 Taperssection.com
Powered by SMF