Become a Site Supporter and Never see Ads again!

Author Topic: clamps  (Read 36655 times)

0 Members and 1 Guest are viewing this topic.

Offline Brian Skalinder

  • Complaint Dept.
  • Trade Count: (28)
  • Needs to get out more...
  • *****
  • Posts: 18868
  • Gender: Male
clamps
« on: April 29, 2003, 05:06:42 PM »

CLAMPS



IMO, no taper should ever be without a clamp.  I get just as much use out of my clamp as I do out of my stand, maybe more.  Here are some commonly used clamps:

Signal Flex MH-10 - this is the one I use and I think it's great (aka Windtech Multi-Position C-Type Clamp)
Rowi ENG
Rowi 76
Rowi 103
Bogen / Manfrotto SuperClamp
Sabrasom SMC
Guitar Center has some plastic clamps that'll work in a fix

or

Check your local musician's store - they often have cheapies and even some of the above on-hand.
« Last Edit: March 04, 2006, 10:48:22 PM by Brian Skalinder »
Milab VM-44 Links > Fostex FR-2LE or
Naiant IPA (tinybox format) >
Roland R-05

Offline tim in jersey

  • Site Supporter
  • Trade Count: (8)
  • Needs to get out more...
  • *
  • Posts: 3786
  • Gender: Male
Re:clamps
« Reply #1 on: May 09, 2003, 11:15:58 PM »
another clamp that's great for clamping to a rail is the cardellini clamp. it's jaws open wider than any other clamp I've seen. a bit pricey but the thing is built like a tank.

http://store.yahoo.com/cinemasupplies/2mmicmoun.html

Offline Brian Skalinder

  • Complaint Dept.
  • Trade Count: (28)
  • Needs to get out more...
  • *****
  • Posts: 18868
  • Gender: Male
my complete clamping setup
« Reply #2 on: March 04, 2006, 10:53:39 PM »
Emailed a version of this off to a local taper recently and thought I'd add it here.  My full clamp setup:

I use a variety of clamping gear depending on the situation.  All in all, I use my clamping gear more often than my mic stand.  Here's what I use (almost all available at B&H Photo - www.bhphotovideo.com - best source I've found, though not always super cheap for little stuff like thread adapters):

Windtech Multi-Position "C" Clamp
Mfr # MPC10 | B&H # WIMPC10
I use this one for clamping to other tapers' stands.  Compact, lightweight, flexible with 2 different orientations for the mic thread stud.  I couldn't get by without one.  I have several, and always carry them with me.

Bogen SuperClamp
Mfr # 2900 | B&H # BO2900
This is the clamp I use for latching on to railings, posts, tables, chairs, shelves, pipes, ceiling beams, light fixtures...damn near anything other than a mic stand.  Bigger and heavier than the MPC above, uber-robust, wide jaws.  Comes with standard 1/4"-20 male threaded stud (see below).  For short rises or adjusting orientation (the stud mounts in only one orientation, unlike the MPC above), I use either the Heavy Duty Flex Arm  or Mini-Extension arm (see below).

Bogen SuperClamp Standard Stud (with 1/4"-20 male thread)
Mfr # 2908 | B&H # BO2908
Comes with the Bogen SuperClamp above.  Requires a 1/4"-20 female > 3/8"-16 thread adapter and a 3/8"-20 female > 5/8"-27 male thread adapter before using with standard 5/8"-27 female microphone / stereo bar threads.  See below for adapters.

Bogen Extension Arm for Mini Clamp (works with SuperClamp, too)
Mfr # 203 | B&H # BO203
Great for extending short distances from the SuperClamp, and for adjusting orientation.  I went without one for a looooong time, using only a (non-Bogen) gooseneck extension.  Now, I have both.  I think one or the other will suffice for most purposes.

Bogen Heavy-Duty Flex Arm
Mfr# 237HD | B&H# BO237HD
Basically just a robust gooseneck extension (like the kind available at a local musicians' store - which I originally used - but beefier).  Includes the appropriate bottom end needed to slot it into the SuperClamp.  The mic end of the extension has a 1/4"-20 male thread, just like the SuperClamp's standard stud above, so it, too, requires adapters in order to attach a standard 5/8"-27 mic thread.  I use this mainly with my Schoeps actives, not sure if it's beefy enough to run full-size mics & shockmounts.

Arca-Swiss Thread Adapter (1/4"-20 female > 3/8"-16 male )
Mfr # 809011 | B&H # ARB.2538
This isn't the exact one I bought, but I can't remember the manufacturer / model / retailer of mine.

Windtech Thread Adapter (3/8"-16 female > 5/8"-27 male)
Mfr # M3 | B&H # WIM3C
This isn't the exact one I bought, but I can't remember the manufacturer / model / shop of mine.

A.P.I.C. Custom 3-Section Extension Pole (28"-78", 5/8"-27 male/female threads on appropriate ends)
The piece de resistance.  I use this in conjunction with the SuperClamp all the time.  I use it regularly at at least half a dozen or so local venues to run my mics up/down/out/beside my clamping space in order to achieve a more optimal mic location.  Custom, though, so it's not cheap - ran me around $75 if I recall (had it for years).  Gets more use than my Bogen 3373 mic stand.  Bogen makes a couple extensions like this, but none as long, and I've found them difficult to track down online.  A.P.I.C's phone #:  201-261-2160.  They also make mic stands, but I prefer the Bogen mic stands.  If you order a custom extension from these guys, they'll want specs on number of sections, closed length, open length, and make sure you tell 'em you want 5/8"-27 adapters on each end - female on the bottom, male on the top.  I'm ordering a new 4-section extension soon, so I still get the ~80" of reach but can close it more compactly to fit on my motorcycle.  And I already have 3 people in line for my old one when I sell!

Alternative extension pole:

Bogen / Manfrotto 3-Section Extension Pole (35" - ~92")
Mfr# 099B | B&H# BO099B (thanks to macdaddy for the heads up that the previous referenced mode, 3019, was discontinued and replaced with this one)
Looks like it has a 5/8"-27 female thread on the bottom, according to the specs on B&H.  Has a combination 5/8" stud and 3/8"-16 male thread tip on the top.  Much less expensive than the custom APIC extension (by about half!).  Wish I could fit a 3' pole on my motorcycle more easily, I'd save myself a few bucks.
« Last Edit: March 22, 2009, 02:16:28 AM by Brian Skalinder »
Milab VM-44 Links > Fostex FR-2LE or
Naiant IPA (tinybox format) >
Roland R-05

Offline Chuck

  • Trade Count: (42)
  • Needs to get out more...
  • *****
  • Posts: 10810
  • Gender: Male
  • time between the notes...
    • My recordings on the LMA
Re: my complete clamping setup
« Reply #3 on: March 05, 2006, 07:34:47 PM »

Windtech Multi-Position "C" Clamp
Mfr # MPC10 | B&H # WIMPC10
I use this one for clamping to other tapers' stands.  Compact, lightweight, flexible with 2 different orientations for the mic thread stud.  I couldn't get by without one.  I have several, and always carry them with me.


When you lose or break the bumper piece that is on the end of the threaded part of this clamp, buy some of those screw-on plastic valve stem covers. I like using them better than the original piece that comes with the clamp. (Bean originally turned me on to this)
« Last Edit: March 06, 2006, 12:01:32 PM by Chuck »
Reality is merely an illusion, albeit a very persistent one.

Microphones: AKG C 480 B comb-ULS/ CK 61/ CK 63, Sennheiser MKE 2 elements,  Audix M1290-o, Micro capsule active cables w/ Naiant PFA's, Naiant MSH-1O, Naiant AKG Active cables, Church CA-11 (cardioid), (1) Nady SCM-1000 (mod)
Pre-amps: Naiant littlebox, Naiant littlekit v2.0, BM2p+ Edirol UA-5, Church STC-9000
Recorders: Sound Devices MixPre-6, iRiver iHP-120 (Rockboxed & RTC mod)

Recordings on the LMA: http://www.archive.org/bookmarks/ChuckM
Recording website & blog: http://www.timebetweenthenotes.com

Offline shaggy

  • Trade Count: (10)
  • Taperssection All-Star
  • ****
  • Posts: 1928
    • dwonk
Re: clamps
« Reply #4 on: March 05, 2006, 08:10:26 PM »


Yep, this is one clamp to have if you are looking for bang for your buck (and weight considerations).  I like the Manfrotto Superclamp alot....it is a piece of art but if you carry two (if you want all configuations you gotta have two) it is a back breaker.

If you can't see why you'd need two superclamps to do anything....look here:
http://taperssection.com/index.php?topic=29789.0


Offline fozzy

  • Trade Count: (2)
  • Needs to get out more...
  • *****
  • Posts: 3810
  • Gender: Male
  • move along, nothing much to see here
Re: clamps
« Reply #5 on: March 05, 2006, 08:49:27 PM »
If you can't see why you'd need two superclamps to do anything....look here:
http://taperssection.com/index.php?topic=29789.0


or here, http://taperssection.com/index.php?topic=40368.0
2 superclamps and some accesories is al little heavy but i can still fit em in my rm-multi and run anywhere

In addition to a clamp I also never leave home w/o this, get any angle of clamp off anything and get the right angle w/ this

http://www.bhphotovideo.com/bnh/controller/home?O=productlist&A=details&Q=&sku=221096&is=REG&addedTroughType=search



requires 3/8 > 5/8 for the base and 1/4" > 5/8" for the top to fit into my all 5/8" system
MK 4V > KCY 250/5 Ig (KS 10I)  > VST62IUg > 722

Offline Krispy D

  • Trade Count: (1)
  • Needs to get out more...
  • *****
  • Posts: 4878
  • Gender: Male
    • my recordings on LMA
Re: clamps
« Reply #6 on: March 05, 2006, 10:11:45 PM »
I've been witing for this thread for a while.  thanks for all the pointers everybody!  now to go spend more money...
Peluso CEMC6, ck4/ck21
Oktava MC012
Sony ECM260f
AT 811

canare star quads
DIY mil spec silvers

DIY (W-ish) mod UA5>JB3
Oade ACM PMD 660
R4


You cannot strengthen the weak by weakening the strong. You cannot help the wage-earner by pulling down the wage-payer. You cannot help the poor by destroying the rich. You cannot help men permanently by doing for them what they could and should do for themselves.
~Rev. William J. H. Boetcker (not Lincoln)

Offline johnw

  • Trade Count: (11)
  • Needs to get out more...
  • *****
  • Posts: 3818
  • Gender: Male
    • My cd List
Re: clamps
« Reply #7 on: March 07, 2006, 11:18:26 AM »
I didn't see this one mentioned. It's my personal favorite.

ATS/Pedco Ultraclamp
Schoeps MK41 & MK4V  |  Schoeps CMC6, Schoeps KCY, AKI/2C, PFA, Nbox Cable/PFA  |  Grace V2, Nbox Platinum  |  SD744T, SD MixPre 6, Sony PCM M10

Canon 16-35mm/2.8L mkii, 24-70mm/2.8L, 70-200mm/2.8L IS, 50mm/1.8 mkii, 135mm/2L, 100mm/2.8L IS, Sigma 35mm/1.4 A  |  Canon 5D mk4

Offline anhisr

  • Trade Count: (6)
  • Needs to get out more...
  • Posts: 2974
  • Gender: Male
Re: clamps
« Reply #8 on: March 07, 2006, 11:39:07 AM »
I am looking for a 1/4 to 5/8 for the top of a clamp and am having problems finding one.  Maybe I am just not getting myself understood when asking.  Any help
Audio: Neumann KM 100> 20, 30, 40, 43 or 50 > V3 > MT II (love that M/S)
Still Camera Body: Canon D5 Mark II
Canon Lenses:  16-35mm f2.8L II USM; 28-135mm f3.5-5.6 IS USM; 70-200mm f2.8L IS USM
Video Canon HF R30

archive  http://www.archive.org/bookmarks/anhisr

Offline fozzy

  • Trade Count: (2)
  • Needs to get out more...
  • *****
  • Posts: 3810
  • Gender: Male
  • move along, nothing much to see here
Re: clamps
« Reply #9 on: March 07, 2006, 11:56:58 AM »
I am looking for a 1/4 to 5/8 for the top of a clamp and am having problems finding one.  Maybe I am just not getting myself understood when asking.  Any help

not the best way but this is what I use and then I have a 3/8 > 5/8 adapter

http://www.bhphotovideo.com/bnh/controller/home?O=productlist&A=details&Q=&sku=5596&is=REG&addedTroughType=search
MK 4V > KCY 250/5 Ig (KS 10I)  > VST62IUg > 722

Offline Brian Skalinder

  • Complaint Dept.
  • Trade Count: (28)
  • Needs to get out more...
  • *****
  • Posts: 18868
  • Gender: Male
Re: clamps
« Reply #10 on: March 07, 2006, 01:03:01 PM »
ATS/Pedco Ultraclamp

I used a pair of these for a while, but found they did not attach very securely to mic stands - even when I tightened as much as physically possible, the weight of a single LD mic caused the clamp to split.  But, if it works for you, great!  Especially since the thing is so versatile.  Wish it had worked for me.
Milab VM-44 Links > Fostex FR-2LE or
Naiant IPA (tinybox format) >
Roland R-05

Offline Massive Dynamic

  • Trade Count: (21)
  • Taperssection All-Star
  • ****
  • Posts: 1421
  • Gender: Male
  • 20 years of the best in apocalyptic gothic metal
Re: clamps
« Reply #11 on: March 07, 2006, 02:27:15 PM »
I am looking for a 1/4 to 5/8 for the top of a clamp and am having problems finding one.  Maybe I am just not getting myself understood when asking.  Any help
These two sources may have what you are looking for.
http://www.micsupply.com/standaccessories.htm
Check the bottom of the page

http://www.wesdooley.com/aea/Modular_Microphone_Stands.html
This is a link to a pdf price list.
Naiant X-X > SP-SPSB-1 > M10
Superlux S502 > Denecke PS-2 > Hosa MIT-435 > M10

Offline johnw

  • Trade Count: (11)
  • Needs to get out more...
  • *****
  • Posts: 3818
  • Gender: Male
    • My cd List
Re: clamps
« Reply #12 on: March 10, 2006, 01:24:27 PM »
ATS/Pedco Ultraclamp

I used a pair of these for a while, but found they did not attach very securely to mic stands - even when I tightened as much as physically possible, the weight of a single LD mic caused the clamp to split.  But, if it works for you, great!  Especially since the thing is so versatile.  Wish it had worked for me.

Oh - definitely not meant for LD mics - sorry about that. But these work great with my SD AKGs.
Schoeps MK41 & MK4V  |  Schoeps CMC6, Schoeps KCY, AKI/2C, PFA, Nbox Cable/PFA  |  Grace V2, Nbox Platinum  |  SD744T, SD MixPre 6, Sony PCM M10

Canon 16-35mm/2.8L mkii, 24-70mm/2.8L, 70-200mm/2.8L IS, 50mm/1.8 mkii, 135mm/2L, 100mm/2.8L IS, Sigma 35mm/1.4 A  |  Canon 5D mk4

Offline BC

  • Trade Count: (1)
  • Needs to get out more...
  • *****
  • Posts: 2269
  • Gender: Male
  • Bongo Bongo
In: DPA4022>V3>Microtracker/D8

Out: Morrison ELAD>Adcom GFA555mkII>Martin Logan Aerius i

Offline anhisr

  • Trade Count: (6)
  • Needs to get out more...
  • Posts: 2974
  • Gender: Male
Re: clamps
« Reply #14 on: March 06, 2008, 02:31:35 PM »
probably the most versatile clamp made.  This thing works at any angle you need. 
Audio: Neumann KM 100> 20, 30, 40, 43 or 50 > V3 > MT II (love that M/S)
Still Camera Body: Canon D5 Mark II
Canon Lenses:  16-35mm f2.8L II USM; 28-135mm f3.5-5.6 IS USM; 70-200mm f2.8L IS USM
Video Canon HF R30

archive  http://www.archive.org/bookmarks/anhisr

Offline Brian Skalinder

  • Complaint Dept.
  • Trade Count: (28)
  • Needs to get out more...
  • *****
  • Posts: 18868
  • Gender: Male
Re: clamps
« Reply #15 on: March 06, 2008, 07:03:38 PM »
probably the most versatile clamp made.  This thing works at any angle you need. 

If it supports your mics, that is.  IME, the ultraclamp wasn't robust enough to handle a single AKG C414B-XLS + shockmount.   :-\
Milab VM-44 Links > Fostex FR-2LE or
Naiant IPA (tinybox format) >
Roland R-05

Offline anhisr

  • Trade Count: (6)
  • Needs to get out more...
  • Posts: 2974
  • Gender: Male
Re: clamps
« Reply #16 on: March 06, 2008, 07:05:26 PM »
I guess I should have said "If you have small diameter microphones." 
Audio: Neumann KM 100> 20, 30, 40, 43 or 50 > V3 > MT II (love that M/S)
Still Camera Body: Canon D5 Mark II
Canon Lenses:  16-35mm f2.8L II USM; 28-135mm f3.5-5.6 IS USM; 70-200mm f2.8L IS USM
Video Canon HF R30

archive  http://www.archive.org/bookmarks/anhisr

Offline shaggy

  • Trade Count: (10)
  • Taperssection All-Star
  • ****
  • Posts: 1928
    • dwonk
Re: clamps
« Reply #17 on: March 06, 2008, 09:51:00 PM »
I use the Ultrapod I most all the time these days.  Picked up from Campmor eons ago for $8.  Takes up hardly any space in the bag.  It is probably only good for active set ups as that is what I use exclusively (I have no bodies for the Neumanns and Schoeps).



Th velcro strap is amazingly handy, I wrap it around mic stand poles and fixtures from the ceiling.  What I do to prevent it from squirreling around is: wrap small rubber bands around the leg that are not 'L shaped', when the legs are folded up the rubber bands give that friction that is necessary to hold the whole thing in place without it sliding down or around a pole.  In the pic, there are what appears to be rubber feet, mine does not have those and I suspect that they may act like the rubber bands I am using.

Man, rubber bands are the most amazing things.  I use them for EVERYTHING!

Offline cybergaloot

  • Trade Count: (7)
  • Needs to get out more...
  • *****
  • Posts: 4079
  • Gender: Male
  • Poohbah!
Re: clamps
« Reply #18 on: March 06, 2008, 10:55:36 PM »
Just for grins I thought I'd show this one. It obviously has very limited possibilities but it was already in my tool box as part of a Central Tools brake rotor run-out measuring device. The threads at 1/4 X 20 and the flex section locks fairly solidly but I wouldn't want to hang much weight on it.
--
Walter

Everybody is ignorant, only on different subjects. Will Rogers

this>that>the other

Offline NOLAfishwater

  • is not taping much these days
  • Trade Count: (72)
  • Needs to get out more...
  • *****
  • Posts: 6344
  • Gender: Male
  • I LIKE FISHIN
Re: clamps
« Reply #19 on: May 28, 2008, 02:42:25 PM »
another great thread about clamping. very cool extension arm. Check it out.

http://taperssection.com/index.php/topic,103678.0.html

Offline newplanet7

  • Hasn't heard a muddy 460/480 tape. EVER. Mike Hawk
  • Trade Count: (5)
  • Needs to get out more...
  • *****
  • Posts: 3530
  • Gender: Male
  • The Place To Be...... Akustische u. Kino-Geräte
Re: clamps
« Reply #20 on: February 07, 2009, 09:15:36 PM »
So I'm a little drunk tonight and would like to share what I did for my windtech clamp.
The rubber/plastic piece on the end is junk.
So I happen to have been drinking nips of belvedere vodka which comes with a mini hard rubber
composite cork.
I bored out the middle with some cutters and an exacto. Just enough to get the threads from the clamp in.
Then held the cork with chanel locks and tightened the clamp into it.
Whalla........ A snug fit that doesn't seem to be deteriorating at all.

MILAB VM-44 Classic~> Silver T's~> Busman PMD660
News From Phish: Will tour as opening act for Widespread Panic for Summer
hahaha never happen, PHiSH is waaaaayyyy better the WSP

They both ain't got nothing on MMW... Money spent wisely if you ask me...


FYI, it is a kick ass recording of a bunch of pretend-a-hippies talking.

Offline macdaddy

  • Trade Count: (10)
  • Needs to get out more...
  • *****
  • Posts: 7657
Re: clamps
« Reply #21 on: February 10, 2009, 11:57:20 AM »


Yep, this is one clamp to have if you are looking for bang for your buck (and weight considerations).  I like the Manfrotto Superclamp alot....it is a piece of art but if you carry two (if you want all configuations you gotta have two) it is a back breaker.

If you can't see why you'd need two superclamps to do anything....look here:
http://taperssection.com/index.php?topic=29789.0




hey, shaggy!

what piece(s) (part #s..?) are you using to connect the two superclamps..?

thanks.

would like to share what I did for my windtech clamp.
The rubber/plastic piece on the end is junk.
So I happen to have been drinking nips of belvedere vodka which comes with a mini hard rubber
composite cork.
I bored out the middle with some cutters and an exacto. Just enough to get the threads from the clamp in.
Then held the cork with chanel locks and tightened the clamp into it.
Whalla........ A snug fit that doesn't seem to be deteriorating at all.

i have no idea what you are talking about (and i am trying to understand ;) )...

i also saw somewhere that you could use valve covers, but what kind, and where to get them - i have no idea (i need something though, 'cos i agree the rubber end for those windtech clamps sucks)...

-macdaddy ++

akg c422 > s42 > lunatec v2 > ad2k+ > roland r-44

Offline Brian Skalinder

  • Complaint Dept.
  • Trade Count: (28)
  • Needs to get out more...
  • *****
  • Posts: 18868
  • Gender: Male
Re: clamps
« Reply #22 on: February 10, 2009, 12:05:30 PM »
Pretty sure that's the Bogen extension arm.  I believe it's the Bogen 203 Extension Arm (for Mini Clamp, though it works in the SuperClamp).  They make a long and short one.  Don't recall whether the 6" extension arm (w/ double-ended spigot) is the long or short, though (probably short). 

Any old rubber Schrader valve cap will do.  I've gotten mine free at my local auto parts store.  They might cost $0.25/ea if you have to buy them.
« Last Edit: March 22, 2009, 02:10:50 AM by Brian Skalinder »
Milab VM-44 Links > Fostex FR-2LE or
Naiant IPA (tinybox format) >
Roland R-05

Offline Krispy D

  • Trade Count: (1)
  • Needs to get out more...
  • *****
  • Posts: 4878
  • Gender: Male
    • my recordings on LMA
Re: clamps
« Reply #23 on: February 10, 2009, 12:22:58 PM »
Pretty sure that's the Bogen extension arm.  They make a long and short one.  Don't recall whether the 6" extension arm (w/ double-ended spigot) is the long or short, though (probably short).

Any old rubber Schrader valve cap will do.  I've gotten mine free at my local auto parts store.  They might cost $0.25/ea if you have to buy them.

you can get em free at any bike shop in the world as well...
Peluso CEMC6, ck4/ck21
Oktava MC012
Sony ECM260f
AT 811

canare star quads
DIY mil spec silvers

DIY (W-ish) mod UA5>JB3
Oade ACM PMD 660
R4


You cannot strengthen the weak by weakening the strong. You cannot help the wage-earner by pulling down the wage-payer. You cannot help the poor by destroying the rich. You cannot help men permanently by doing for them what they could and should do for themselves.
~Rev. William J. H. Boetcker (not Lincoln)

Offline cybergaloot

  • Trade Count: (7)
  • Needs to get out more...
  • *****
  • Posts: 4079
  • Gender: Male
  • Poohbah!
Re: clamps
« Reply #24 on: February 10, 2009, 01:00:57 PM »

Any old rubber Schrader valve cap will do.  I've gotten mine free at my local auto parts store.  They might cost $0.25/ea if you have to buy them.

you can get em free at any bike shop in the world as well...

Or parking lot  >:D
--
Walter

Everybody is ignorant, only on different subjects. Will Rogers

this>that>the other

Offline newplanet7

  • Hasn't heard a muddy 460/480 tape. EVER. Mike Hawk
  • Trade Count: (5)
  • Needs to get out more...
  • *****
  • Posts: 3530
  • Gender: Male
  • The Place To Be...... Akustische u. Kino-Geräte
Re: clamps
« Reply #25 on: February 10, 2009, 08:06:38 PM »

Any old rubber Schrader valve cap will do.  I've gotten mine free at my local auto parts store.  They might cost $0.25/ea if you have to buy them.

you can get em free at any bike shop in the world as well...

Or parking lot  >:D
Or you can go with my nip bottle suggestion  >:D
MILAB VM-44 Classic~> Silver T's~> Busman PMD660
News From Phish: Will tour as opening act for Widespread Panic for Summer
hahaha never happen, PHiSH is waaaaayyyy better the WSP

They both ain't got nothing on MMW... Money spent wisely if you ask me...


FYI, it is a kick ass recording of a bunch of pretend-a-hippies talking.

Offline bhtoque

  • Trade Count: (3)
  • Needs to get out more...
  • *****
  • Posts: 3308
  • Gender: Male
  • So much music, so little time.
Re: clamps
« Reply #26 on: February 10, 2009, 10:18:18 PM »
I didn't see this one mentioned. It's my personal favorite.

ATS/Pedco Ultraclamp

QFT

Great clamp, small money.

JAson
MG 200/210/270
AKG c422>s42>Hydra silver interconnects
AKG 391/92/93>MK 90/3 actives
>AM Hyper-Conductors
Studio Projects LSD2>MiAGi II
>Edirol R-4 (Oade T Mod)

db.etree.org/bhtoque

Offline bhtoque

  • Trade Count: (3)
  • Needs to get out more...
  • *****
  • Posts: 3308
  • Gender: Male
  • So much music, so little time.
Re: clamps
« Reply #27 on: February 10, 2009, 10:20:21 PM »
ATS/Pedco Ultraclamp

I used a pair of these for a while, but found they did not attach very securely to mic stands - even when I tightened as much as physically possible, the weight of a single LD mic caused the clamp to split.  But, if it works for you, great!  Especially since the thing is so versatile.  Wish it had worked for me.

That's really suprising. I've had no problems holding up the LSD2 with mine.

Only problem I've had is the rubber pad coming off, but replacements can be had in sheets at home depot.

JAson
MG 200/210/270
AKG c422>s42>Hydra silver interconnects
AKG 391/92/93>MK 90/3 actives
>AM Hyper-Conductors
Studio Projects LSD2>MiAGi II
>Edirol R-4 (Oade T Mod)

db.etree.org/bhtoque

Offline macdaddy

  • Trade Count: (10)
  • Needs to get out more...
  • *****
  • Posts: 7657
Re: my complete clamping setup
« Reply #28 on: March 21, 2009, 09:33:28 PM »
Pretty sure that's the Bogen extension arm.  They make a long and short one.  Don't recall whether the 6" extension arm (w/ double-ended spigot) is the long or short, though (probably short).

i bought that 042 extension arm, and it wont really work to join two superclamps together because of the angle on the hex bolt end (it doesnt always line up the two superclamps at the right angles; the spigot end obviously rotates 360 degrees). i will, however, use it to get a bit of extension (out, horizontally) when i clamp to a vertical i-beam, which is what i bought it for - thx for the part number...


Alternative extension pole:

Bogen / Manfrotto 3109 Extension Pole (35" - ~91")
Mfr# 3109 | B&H# BO3109
Looks like it has a 5/8"-27 female thread on the bottom, according to the specs on B&H.  Has a combination 5/8" stud and 3/8"-16 male thread tip on the top.  Much less expensive than the custom APIC extension (by about half!).  Wish I could fit a 3' pole on my motorcycle more easily, I'd save myself a few bucks.

evidently, the 3019 is discontinued. i just bought the 099b, which is the replacement model for the 3109 (b+h link). the thing is sweet!! it is sturdy, TALL, and it works great with my superclamp: i use one of those 013 spigots - one end drops into the bottom female slot on the pole (which has its own tension knob), and the other end of the spigot drops into the quick-release hole of the superclamp, allowing the pole to be rotated the full 360 degrees. my only gripe with this extension pole is that it is not air-cushioned (the thing goes high up, and it sure does come down in a hurry  :o ).

my FAVORITE piece of clamping gear is the quick-action superclamp (b+h link). it is identical to the regular superclamp, except for the new quick-action mechanism (which is really simple and cool). the thing LOCKS and RELEASES in a jiffy, yet it is just as sturdy and secure as the standard superclamp. the tighten knob is smaller, too, which is a bonus when using the thing in a tight spot, which i sometimes have to do...

so, my clamp/extension quiver looks like this...

  • manfrotto #635 quick release superclamp
  • manfrotto heavy-duty flex arm
  • manfrotto #099b extension pole
  • manfrotto #042 extension arm
  • manfrotto #013 spigot
  • 1/4" > 3/8" male adapter
  • 3/8" > 5/8" male adapter
  • manfrotto #061 and #061ra joining studs
  • manfrotto #035 standard superclamp
  • windtech msa1 clamp

i dont think that there is anything else i need (other than a good, solid, sturdy stand, which i do also have). the heavy-duty flex arm is the work horse, and does almost anything i need it to do. the only place it lacks is straight-on horizontal extension, which is the purpose of carrying the 042 arm. finally, the 099b pole is used for the bigger extension jobs...

if i had my druthers, i would use my superclamp, and above accessories, 100% of the time; a couple times a year (usually outdoors) i need to use a stand, but in most of the clubs/bars/venues where i record, a clamp is preferable. in fact, the biggest problem i encounter when recording is the footprint of the stand; getting the stand legs off of the floor (by eliminating the stand), and clamping to a table, drink rail, ceiling, i-beam, etc. is really the way to go. i used to think a superclamp was overkill, but i kind of need to use one, considering that i run a large shockmount and the c422; i feel the standard c-type clamp is not sturdy enough. in contrast, my gear is well below the weight limits on the superclamp, pole, and arms...

as far as the spigots go, i have had an old 3/8" by 1/4" one that i have used with my flexarm for years; this new one (#013) is a bit beefier, and is designed to fit in the #042 arm with which it came. i use a 1/4" > 3/8" male adapter so the spigot effectively has 2x 3/8" male ends;  i need to do this because the flex arm tops off with the 3/8" female opening, and to use either of the shockmounts i own, i need to use a 3/8" male end, so i can use the 3/8" > 5/8" male adapter, since the mounts have the standard 5/8" female opening...

for joining the two superclamps together, i picked up the connector studs (#061 and #061RA). to be honest, i don't know if i would bother with this otherwise, but rather than get rid of the 035 clamp when i bought the new quick-action one, i bought the two connector bolts - i have yet to use them, but i am ready if the occasion arises ;)
you dont need these bolts at all - since i have an extra spigot, i use that, and i am not limited to the angles on the studs, since the spigots can rotate 360 degrees...

finally, i have a windtech msa1 clamp for the rare instance when i need to clamp onto someone else's stand. the extension bar on that thing (msa1) is sturdy enough for my gear, and i think the clamp mechanism itself is superior (read "more secure") to what is offered by a standard c-type clamp (which isnt sturdy/beefy enough for my needs)...

now if i could only find like an eighteen inch offset arm that will clamp to the pole and accept the superclamp spigot...


« Last Edit: April 11, 2009, 01:57:15 PM by macdaddy »
-macdaddy ++

akg c422 > s42 > lunatec v2 > ad2k+ > roland r-44

Offline Brian Skalinder

  • Complaint Dept.
  • Trade Count: (28)
  • Needs to get out more...
  • *****
  • Posts: 18868
  • Gender: Male
Re: my complete clamping setup
« Reply #29 on: March 22, 2009, 02:09:24 AM »
i bought that 042 extension arm, and it wont really work to join two superclamps together because of the angle on the hex bolt end (it doesnt always line up the two superclamps at the right angles; the spigot end obviously rotates 360 degrees). i will, however, use it to get a bit of extension (out, horizontally) when i clamp to a vertical i-beam, which is what i bought it for - thx for the part number...

Hmmmm...just checked, and I got the part # wrong.  Sorry!  It's Bogen 203 Extension Arm (for Mini Clamp, though it works in the SuperClamp).  The 203 doesn't have a hex end, it's circular, allowing for variable angle instead of one of 6 angles due to the hex.  Going back to edit my original post...
Milab VM-44 Links > Fostex FR-2LE or
Naiant IPA (tinybox format) >
Roland R-05

Offline macdaddy

  • Trade Count: (10)
  • Needs to get out more...
  • *****
  • Posts: 7657
Re: clamps
« Reply #30 on: March 22, 2009, 12:50:43 PM »
no matter, brian - the 042 is exactly what i needed; sure, a round end piece (instead of the hex bolt) would have been ideal, but the 042 will suit my needs just fine...

-macdaddy ++

akg c422 > s42 > lunatec v2 > ad2k+ > roland r-44

Offline DigiGal

  • AES Associate Member
  • Trade Count: (30)
  • Needs to get out more...
  • *****
  • Posts: 2583
  • Gender: Female
  • Stay healthy and safe!
    • DigiGal Internet Archive Recordings
Re: clamps
« Reply #31 on: September 17, 2012, 01:22:34 PM »
This is another great clamp that I didn't see listed in this thread, it's a bit on the bulky side but very secure and can clamp to just about anything.  Link to a excellent video demonstration of it.

http://www.bhphotovideo.com/c/product/161307-REG/Matthews_420110_Matthellini_Clamp_2.html

http://www.bhphotovideo.com/c/product/686485-REG/Matthews_420113_Extendellini_For_Matthellini_Center.html

Here is a quick photo of the clamp used on a beam without the extendellini.


This is a photo with one extendellini that helps demonstrate the strength of these clamps.
« Last Edit: September 21, 2012, 01:02:15 PM by DigiGal »
Mics: AKG CK91/CK94/CK98/SE300 D-330BT | DPA 4060 4061 4266 | Neumann TLM 103 | Senn ME66/K6/K6RD MKE2 MD421 MD431 | Shure VP88 SM7B SM63L SM58 Anniversary Cables: Gotham GAC-4/1 Quad w/Neutrik EMC | Gotham GAC-2pair w/AKG MK90/3 connectors | DigiGal AES>S/PDIF cable Preamp: SD MixPre-D Recorders: SD MixPre 6 | Marantz PMD 661 Edit: 2011 27" 3.4GHz Quad i7 iMac High Sierra | 2020 13" MBA Quad i7 Catalina | Wave Editor | xACT | Transmission | FCP X 

Offline bryonsos

  • Omni addict
  • Trade Count: (28)
  • Needs to get out more...
  • *****
  • Posts: 2061
  • Gender: Male
  • If it's important, tell me to write it down.
    • LMA uploads
Re: clamps
« Reply #32 on: September 17, 2012, 01:28:14 PM »
This is another great clamp that I didn't see listed in this thread, it's a bit on the bulky side but very secure and can clamp to just about anything.  Link to a excellent excellent video demonstration of it.

http://www.bhphotovideo.com/c/product/161307-REG/Matthews_420110_Matthellini_Clamp_2.html

http://www.bhphotovideo.com/c/product/686485-REG/Matthews_420113_Extendellini_For_Matthellini_Center.html

BEST clamp EVER!! It is 100% my go to clamp. The width it can open alone kicks Superclamp ass, but the shape and config of the jaws make it a no brainer. This thing will clamp just about anywhere you need.
Mics: 3 Zigma Chi HA-FX (COL-251, c, h, o-d, o-f) / Avenson STO-2 / Countryman B3s
Pres: CA-Ugly / Naiant Tinyhead / SD MixPre
Decks: Roland R-44 / Sony PCM-M10
GAKables
Dead Muppets

My recordings LMA / BT / TTD

Offline macdaddy

  • Trade Count: (10)
  • Needs to get out more...
  • *****
  • Posts: 7657
Re: clamps
« Reply #33 on: September 17, 2012, 01:51:09 PM »
been using this thing for a while now. the extension piece is nice, and can come in handy for those uber-wide beams. the other piece that compliments this setup, big time, is the magic finger, which adds stability with no slippage. I attach my manfrotto 99b pole to it at all sorts of angles. you need to use a cotter pin with it to keep the magic finger from sliding, but that is easy enough, and the holes are already there.

glad to see others finally jumping on the bandwagon.

magic finger link
-macdaddy ++

akg c422 > s42 > lunatec v2 > ad2k+ > roland r-44

Offline DigiGal

  • AES Associate Member
  • Trade Count: (30)
  • Needs to get out more...
  • *****
  • Posts: 2583
  • Gender: Female
  • Stay healthy and safe!
    • DigiGal Internet Archive Recordings
Re: clamps
« Reply #34 on: September 17, 2012, 02:35:21 PM »
I'll also add the "Mini Cardellini Microphone Clamp with 3/8" Thread" to the list.  It's excellent for clamping to a stand and Rycote INV shock mounts will thread right on, no adapters necessary.


« Last Edit: September 19, 2012, 11:17:13 AM by DigiGal »
Mics: AKG CK91/CK94/CK98/SE300 D-330BT | DPA 4060 4061 4266 | Neumann TLM 103 | Senn ME66/K6/K6RD MKE2 MD421 MD431 | Shure VP88 SM7B SM63L SM58 Anniversary Cables: Gotham GAC-4/1 Quad w/Neutrik EMC | Gotham GAC-2pair w/AKG MK90/3 connectors | DigiGal AES>S/PDIF cable Preamp: SD MixPre-D Recorders: SD MixPre 6 | Marantz PMD 661 Edit: 2011 27" 3.4GHz Quad i7 iMac High Sierra | 2020 13" MBA Quad i7 Catalina | Wave Editor | xACT | Transmission | FCP X 

Offline DigiGal

  • AES Associate Member
  • Trade Count: (30)
  • Needs to get out more...
  • *****
  • Posts: 2583
  • Gender: Female
  • Stay healthy and safe!
    • DigiGal Internet Archive Recordings
Re: clamps
« Reply #35 on: October 17, 2012, 02:25:37 PM »
A balcony rail setup with modded AKG MK90/3 active cable, CK91 (cardiod's) in ORTF configuration mounted on
AKG H98 Holders on Vark Bar, Rycote INV Shock Mount, Manfrotto Articulated Arm and Matthellini Clamp.
To connect the Articulated Arm I used a Manfrotto MA158 as pictured, which is linked here for purchase
« Last Edit: December 18, 2012, 05:23:24 PM by DigiGal »
Mics: AKG CK91/CK94/CK98/SE300 D-330BT | DPA 4060 4061 4266 | Neumann TLM 103 | Senn ME66/K6/K6RD MKE2 MD421 MD431 | Shure VP88 SM7B SM63L SM58 Anniversary Cables: Gotham GAC-4/1 Quad w/Neutrik EMC | Gotham GAC-2pair w/AKG MK90/3 connectors | DigiGal AES>S/PDIF cable Preamp: SD MixPre-D Recorders: SD MixPre 6 | Marantz PMD 661 Edit: 2011 27" 3.4GHz Quad i7 iMac High Sierra | 2020 13" MBA Quad i7 Catalina | Wave Editor | xACT | Transmission | FCP X 

Offline F.O.Bean

  • Team Schoeps Tapir that
  • Trade Count: (126)
  • Needs to get out more...
  • *****
  • Posts: 40690
  • Gender: Male
  • Taperus Maximus
    • MediaFire Recordings
Re: clamps
« Reply #36 on: October 29, 2012, 09:00:36 PM »
been using this thing for a while now. the extension piece is nice, and can come in handy for those uber-wide beams. the other piece that compliments this setup, big time, is the magic finger, which adds stability with no slippage. I attach my manfrotto 99b pole to it at all sorts of angles. you need to use a cotter pin with it to keep the magic finger from sliding, but that is easy enough, and the holes are already there.

glad to see others finally jumping on the bandwagon.

magic finger link


how do you connect a superclamp to the magic finger? would a 5/8" stud fit in the bottom of it? and then i could put my lowel full pole at any angle, correct?
Schoeps MK 4V & MK 41V ->
Schoeps 250|0 KCY's (x2) ->
Naiant +60v|Low Noise PFA's (x2) ->
DarkTrain Right Angle Stubby XLR's (x3) ->
Sound Devices MixPre-6 & MixPre-3

http://www.archive.org/bookmarks/diskobean
http://www.archive.org/bookmarks/Bean420
http://bt.etree.org/mytorrents.php
http://www.mediafire.com/folder/j9eu80jpuaubz/Recordings

 

RSS | Mobile
Page created in 0.384 seconds with 66 queries.
© 2002-2024 Taperssection.com
Powered by SMF