Become a Site Supporter and Never see Ads again!

Author Topic: Tascam DR2d - part 2  (Read 59341 times)

0 Members and 1 Guest are viewing this topic.

Offline yug du nord

  • uncleyug>Snowman>
  • Trade Count: (53)
  • Needs to get out more...
  • *****
  • Posts: 4916
  • made with natural flavor
Re: Tascam DR2d - part 2
« Reply #345 on: July 12, 2017, 08:27:24 PM »
Can someone refresh my memory on how to set the DR-2d up for dual recording and what level should mic and line be run??  Thanks

Line : 95 minimum
Mic  : 67 minimum
.....got a blank space where my mind should be.....

Offline Andrea82

  • Trade Count: (0)
  • Taperssection Regular
  • **
  • Posts: 56
  • Gender: Male
    • The 1st and only italian site about Eric Clapton
Re: Tascam DR2d - part 2
« Reply #346 on: September 09, 2017, 08:56:11 AM »
Please anyone can tell me what's new with the 1.03 firmware?

Offline Elguapo511

  • Trade Count: (0)
  • Taperssection Newbie
  • *
  • Posts: 1
Re: Tascam DR2d - part 2
« Reply #347 on: September 11, 2017, 11:27:11 PM »
Hi all,

Just joined the forum this make the most of my dr2d.

I don't see any notes on monitoring while recording.
Is it correct that you can only monitor the ' Mic in' during recording?

I know that you can view the levels of both the mic AND line in separately,
But can you listen to the line in and mic in separately?

Offline Gutbucket

  • record > listen > revise technique
  • Trade Count: (13)
  • Needs to get out more...
  • *****
  • Posts: 11361
  • Gender: Male
Re: Tascam DR2d - part 2
« Reply #348 on: September 15, 2017, 10:58:48 AM »
Please anyone can tell me what's new with the 1.03 firmware?

Primary change was vastly increased battery run time. It was basically unusable for concert taping without an external battery before that update.  There may have been other changes I can't recall, but that was the big and most welcome change which made it a viable deck for taping.
volition > vibrations > voltages > numeric values | numeric values > voltages > vibrations > virtual teleportation time-machine experience

Offline Gutbucket

  • record > listen > revise technique
  • Trade Count: (13)
  • Needs to get out more...
  • *****
  • Posts: 11361
  • Gender: Male
Re: Tascam DR2d - part 2
« Reply #349 on: September 15, 2017, 11:03:13 AM »
I don't see any notes on monitoring while recording.
Is it correct that you can only monitor the ' Mic in' during recording?

I know that you can view the levels of both the mic AND line in separately,
But can you listen to the line in and mic in separately?

Correct.  You can switch visual metering back and forth at any time by pressing the DUAL button.  But you can only audio monitor the mic-input while recording.  You cannot audio-monitor the Line-input while recording.

During playback you can switch between and play the line-in and mic-in file successively, but cannot switch between them mid-stream.
volition > vibrations > voltages > numeric values | numeric values > voltages > vibrations > virtual teleportation time-machine experience

 

RSS | Mobile
Page created in 0.093 seconds with 27 queries.
© 2002-2017 Taperssection.com
Powered by SMF
Website Design by Foxtrot Media, Inc., a Baltimore Website Company