Become a Site Supporter and Never see Ads again!
« previous next »
Pages: [1]   Go Down

Author Topic: got my V3 switched over.now what about my P1??  (Read 2760 times)

0 Members and 1 Guest are viewing this topic.

Offline Just Taper Mark from NC

  • when the bass kicks..all I need is a mic and a stage and mix.
  • Trade Count: (2)
  • Needs to get out more...
  • *****
  • Posts: 7073
  • Gender: Male
  • Dodgertown 90090
got my V3 switched over.now what about my P1??
« on: October 26, 2006, 03:11:13 AM »
so I am now running the V3 on a wally and have greatly reduced the weight in my
back by dropping one of the 6v SLA's  :) I would like to ditch the other too but was
wondering if the p1's will run off the lithiums and if so who's doing power cables  ???

I do have an extra "hack" cable that is p1>open end for power supply so no worries
about screwing that up.any help is appreciated as always  ;)
Logged
Positive vibration man.That's what makes it work.That's reggae music.You can't look away because it is real.You listen to what I sing because I mean what I sing,there's no secret,no big deal.,Just honesty,that's all."-Hon. Robert Nesta Marley 1977

Offline svenkid

  • Trade Count: (0)
  • Needs to get out more...
  • *****
  • Posts: 3564
  • Gender: Male
  • Take Time to Listen!
Re: got my V3 switched over.now what about my P1??
« Reply #1 on: October 26, 2006, 03:54:52 PM »
What did you do to your v3? My bag is too heavy right now.
Logged
Quote from: pmonk66 on September 25, 2008, 09:03:53 AM
Seriously, the band makes the music. Tapers just point mics in the right direction and hit "record".

Quote from: Audßall on February 02, 2006, 12:54:42 AM
That's good to hear!  The last patcher I had complained about my AKGs, fluffed schoeps for about 15 minutes, stayed patched in, and farted on me all night long.
rig: Neuman u89s > Lunatec V3 > MT(24)/JB3(16)
http://db.etree.org/svenkid

Um, in my room, one seam is a little off and I stare at it constantly. It's, like, destroying me.

Offline dnsacks

  • Trade Count: (9)
  • Taperssection All-Star
  • ****
  • Posts: 1640
Re: got my V3 switched over.now what about my P1??
« Reply #2 on: October 26, 2006, 04:38:35 PM »
Quote from: svenkid on October 26, 2006, 03:54:52 PM
What did you do to your v3? My bag is too heavy right now.

I believe he simply purchased a walmart 9v lithium ion battery to power the v3, getting rid of one of his larger/heavier SLA batteries.

Logged

thepassionofyonder

  • Guest
  • Trade Count: (0)
Re: got my V3 switched over.now what about my P1??
« Reply #3 on: October 31, 2006, 11:48:41 PM »
Quote from: Mark S. on October 26, 2006, 03:11:13 AM
so I am now running the V3 on a wally and have greatly reduced the weight in my
back by dropping one of the 6v SLA's  :) I would like to ditch the other too but was
wondering if the p1's will run off the lithiums and if so who's doing power cables  ???

I do have an extra "hack" cable that is p1>open end for power supply so no worries
about screwing that up.any help is appreciated as always  ;)

i run my p1 with the 7.2 volt lithiums, no problems.
cant comment on the 9 volt though.
Logged

Offline Just Taper Mark from NC

  • when the bass kicks..all I need is a mic and a stage and mix.
  • Trade Count: (2)
  • Needs to get out more...
  • *****
  • Posts: 7073
  • Gender: Male
  • Dodgertown 90090
Re: got my V3 switched over.now what about my P1??
« Reply #4 on: November 01, 2006, 01:00:11 AM »
cool.who made your cable or did you DIY? I'm not to handy with the solder gun,duct tape
is more my specialty  :P
Logged
Positive vibration man.That's what makes it work.That's reggae music.You can't look away because it is real.You listen to what I sing because I mean what I sing,there's no secret,no big deal.,Just honesty,that's all."-Hon. Robert Nesta Marley 1977

thepassionofyonder

  • Guest
  • Trade Count: (0)
Re: got my V3 switched over.now what about my P1??
« Reply #5 on: November 01, 2006, 06:51:01 PM »
Quote from: Mark S. on November 01, 2006, 01:00:11 AM
cool.who made your cable or did you DIY? I'm not to handy with the solder gun,duct tape
is more my specialty  :P

diy
its as simple as you make it.
you can always splice the wires and duct tape them.
i used elec. tape and shirk sleeve from ratshack.
Logged
Pages: [1]   Go Up
« previous next »
 

RSS | Mobile
Page created in 0.066 seconds with 34 queries.
© 2002-2024 Taperssection.com
Powered by SMF