Become a Site Supporter and Never see Ads again!

Author Topic: Tasmcam Dr-44 Help(new)  (Read 2603 times)

0 Members and 1 Guest are viewing this topic.

Offline fuzzytreebeard

  • Trade Count: (2)
  • Taperssection Newbie
  • *
  • Posts: 26
Tasmcam Dr-44 Help(new)
« on: February 19, 2017, 02:00:15 PM »
I am attempting to get all 4 channels to record. When I'm finished recording it creates a file for channel 3 & 4 but no audio plays from the files nor do they register on the device as receiving audio (bars jumping up and down). I had a pair of mics plugged in as well last night. On 4 ch mode please if anyone has any ideas please let me know.

Offline willndmb

  • Trade Count: (17)
  • Needs to get out more...
  • *****
  • Posts: 6792
  • Gender: Male
Re: Tasmcam Dr-44 Help(new)
« Reply #1 on: February 19, 2017, 06:18:12 PM »
Did you have levels for all four?
Were they showing as mono or stereo pairs?

I'm also assuming you saw the firmware upgrade, did you install it?
If yes, did you have this issue at all before? If not, suggest doing it.

Here is the manual of you need it too http://tascam.com/content/downloads/products/861/dr-44wl_om_ve_2.pdf
« Last Edit: February 19, 2017, 06:19:57 PM by willndmb »
Mics - AKG ck61/ck63 (c480b & Naiant actives), SP-BMC-2
XLR Cables - Silver Path w/Darktrain stubbies
Interconnect Cables - Dogstar (XLR), Darktrain (RCA > 1/8) (1/8 > 1/8), and Kind Kables (1/8f > 1/4)
Preamps - Naiant Littlebox & Tinybox
Recorders - PCM-M10 & DR-60D

Offline mysticeyes

  • Trade Count: (21)
  • Taperssection Regular
  • **
  • Posts: 192
Re: Tasmcam Dr-44 Help(new)
« Reply #2 on: February 20, 2017, 08:17:01 PM »
Did channels 3 & 4 have phantom power turned on?

Offline fuzzytreebeard

  • Trade Count: (2)
  • Taperssection Newbie
  • *
  • Posts: 26
Re: Tasmcam Dr-44 Help(new)
« Reply #3 on: February 21, 2017, 03:30:58 PM »
No they did not. Is that the button I slide that says phantom power + mic

Offline willndmb

  • Trade Count: (17)
  • Needs to get out more...
  • *****
  • Posts: 6792
  • Gender: Male
Re: Tasmcam Dr-44 Help(new)
« Reply #4 on: February 21, 2017, 09:24:28 PM »
No they did not. Is that the button I slide that says phantom power + mic
yes, depending on the mics they may need phantom/48v to run orrrr they may not
Mics - AKG ck61/ck63 (c480b & Naiant actives), SP-BMC-2
XLR Cables - Silver Path w/Darktrain stubbies
Interconnect Cables - Dogstar (XLR), Darktrain (RCA > 1/8) (1/8 > 1/8), and Kind Kables (1/8f > 1/4)
Preamps - Naiant Littlebox & Tinybox
Recorders - PCM-M10 & DR-60D

 

RSS | Mobile
Page created in 0.074 seconds with 33 queries.
© 2002-2024 Taperssection.com
Powered by SMF