Become a Site Supporter and Never see Ads again!

Author Topic: My SRS 3D printed microphone bars  (Read 11704 times)

0 Members and 1 Guest are viewing this topic.

Offline noahbickart

  • phishrabbi
  • Site Supporter
  • Trade Count: (33)
  • Needs to get out more...
  • *
  • Posts: 2554
  • Gender: Male
  • So now I wander over grounds of light...
My SRS 3D printed microphone bars
« on: July 28, 2017, 09:16:23 AM »
https://www.shapeways.com/product/W5BGSBPST/hybrid-schoeps-nbobs?li=shareProduct
Newest Bar, meant for OTS PAS taping with 60° angles. 21cm for the mk41v and 30cm for the mk22 (Stereophonic zoom used to match Cardioids in DIN Recording angle, with the different capsules and angles). This bar can accommodate big windscreens for outdoor use. 

https://www.shapeways.com/product/WLTJKUU2H/din-nos-combo-mount?optionId=60523604
DIN/NOS Combo Mount for Schoeps with NBob active cables. Upper pair (20cm) for side-address capsules. Lower pair (30cm @ 90°) for end-address capsules.

https://www.shapeways.com/product/MPPBSUT26/ms-xy-schoeps-with-nbob-actives?optionId=60409239
X/Y or M/S for Schoeps vertical capsules.

https://www.shapeways.com/product/DQ3TZRTAK/hybrid-schoeps-w-n-bob-actives?optionId=60996905
Mounts for 3 Pairs of Schoeps. Outside pair: 70 degrees 35 cm (for the mk22, essentially the same Recording angle as Cards NOS, but modified using the stereophonic zoom for narrower angle and the mk22), plus two vertical pairs, at 30 cm
and 20 cm. This bar is for indoors only, and can not accommodate big windscreens for outdoor use.
Recording:
Capsules: Schoeps mk41v (x2), mk22 (x2), mk3 (x2), mk21 & mk8
Cables: 2x nbob KCY, 1 pair nbob actives, GAKables 10' & 20' 6-channel snakes, Darktrain 2 & 4 channel KCY and mini xlr extensions:
Preamps:    Schoeps VMS 02iub, Naiant IPA, Sound Devices Mixpre6 I
Recorders: Sound Devices Mixpre6 I, Sony PCM m10

Home Playback: Mac Mini> Mytek Brooklyn+> McIntosh MC162> Eminent Tech LFT-16; Musical Fidelity xCan v2> Hifiman HE-4XX / Beyerdynamic DT880

Office Playback: iMac> Grace m903> AKG k701 / Hifiman HE-400

Offline dactylus

  • Site Supporter
  • Trade Count: (62)
  • Needs to get out more...
  • *
  • Posts: 5992
  • Gender: Male
  • Maplewood, MN
Re: My SRS 3D printed microphone bars
« Reply #1 on: July 28, 2017, 10:31:06 AM »

Nice bars Noah!  I think that I'm going to pick up the newest bar that you posted for my mk22's & mk4V's.
hot licks > microphones > recorder



...ball of confusion, that's what the world is today, hey hey...

Offline noahbickart

  • phishrabbi
  • Site Supporter
  • Trade Count: (33)
  • Needs to get out more...
  • *
  • Posts: 2554
  • Gender: Male
  • So now I wander over grounds of light...
Re: My SRS 3D printed microphone bars
« Reply #2 on: July 28, 2017, 10:33:29 AM »

Nice bars Noah!  I think that I'm going to pick up the newest bar that you posted for my mk22's & mk4V's.

That bar was designed for the mk41v but would likely work with the 4v as well.

I'm going to run mk22 and mk41v pairs on that bar along with a mk4v/mk8 M/S rig on Sunday at Phish
Recording:
Capsules: Schoeps mk41v (x2), mk22 (x2), mk3 (x2), mk21 & mk8
Cables: 2x nbob KCY, 1 pair nbob actives, GAKables 10' & 20' 6-channel snakes, Darktrain 2 & 4 channel KCY and mini xlr extensions:
Preamps:    Schoeps VMS 02iub, Naiant IPA, Sound Devices Mixpre6 I
Recorders: Sound Devices Mixpre6 I, Sony PCM m10

Home Playback: Mac Mini> Mytek Brooklyn+> McIntosh MC162> Eminent Tech LFT-16; Musical Fidelity xCan v2> Hifiman HE-4XX / Beyerdynamic DT880

Office Playback: iMac> Grace m903> AKG k701 / Hifiman HE-400

Offline fobstl

  • Trade Count: (4)
  • Taperssection All-Star
  • ****
  • Posts: 1629
Re: My SRS 3D printed microphone bars
« Reply #3 on: July 28, 2017, 11:04:00 AM »
The bars that Scott is creating are truly awesome. I currently have him working on a Kangol mount that looks like it is going to be pretty cool.

Offline LiveOnTape

  • Trade Count: (9)
  • Taperssection Newbie
  • *
  • Posts: 21
Re: My SRS 3D printed microphone bars
« Reply #4 on: July 29, 2017, 03:03:11 PM »

https://www.shapeways.com/product/MPPBSUT26/ms-xy-schoeps-with-nbob-actives?optionId=60409239
X/Y or M/S for Schoeps vertical capsules.


The M/S clip looks really cool.  Do you know the size of the clips for nBobs?  I use two AKG M90 active cables with CK94 figure 8 caps for MS/Blumline.  They look very similar, and have a 12mm clip.  Would this fit?  or do you do custom orders to make one that does? 

Also, are those just small clips back to back with 20mm clip, then just a 20mm post (three pieces)?  If so, I can see these being used in my double M/S rig where I want to use a back-to-back clip onto the AKG's 19mm body (facing backwards). 

Great work,
L
« Last Edit: July 29, 2017, 03:15:55 PM by LiveOnTape »
Recs: Sony PCM-M10 | Mixpre6 | A&H Qu-24 Qu-Drive
Mics: AKGs w CK91,92,94,97,98  | Oktava MK-012 mod | Audix M1290/1255 | Countryman B3s

Offline dactylus

  • Site Supporter
  • Trade Count: (62)
  • Needs to get out more...
  • *
  • Posts: 5992
  • Gender: Male
  • Maplewood, MN
Re: My SRS 3D printed microphone bars
« Reply #5 on: July 30, 2017, 11:05:09 AM »

Nice bars Noah!  I think that I'm going to pick up the newest bar that you posted for my mk22's & mk4V's.

That bar was designed for the mk41v but would likely work with the 4v as well.

I'm going to run mk22 and mk41v pairs on that bar along with a mk4v/mk8 M/S rig on Sunday at Phish

Yes, I saw that you had the bar constructed for mk41v's but it should also be effective for the mk4v's that I run.

 :coolguy:
hot licks > microphones > recorder



...ball of confusion, that's what the world is today, hey hey...

Offline dactylus

  • Site Supporter
  • Trade Count: (62)
  • Needs to get out more...
  • *
  • Posts: 5992
  • Gender: Male
  • Maplewood, MN
Re: My SRS 3D printed microphone bars
« Reply #6 on: July 30, 2017, 12:53:51 PM »

I'm going to run mk22 and mk41v pairs on that bar along with a mk4v/mk8 M/S rig on Sunday at Phish

It will be interesting to hear the mk4v/mk8 M/S rig in action.  Have a good time this evening!
hot licks > microphones > recorder



...ball of confusion, that's what the world is today, hey hey...

Offline acidjack

  • Site Supporter
  • Trade Count: (37)
  • Needs to get out more...
  • *
  • Posts: 5845
  • Gender: Male
Re: My SRS 3D printed microphone bars
« Reply #7 on: July 30, 2017, 03:34:22 PM »
The bars that Scott is creating are truly awesome. I currently have him working on a Kangol mount that looks like it is going to be pretty cool.

Could you please remember to post that when it's done? Or if there's a place to buy one now, I'd love a link...
Mics: Schoeps MK4V, MK41V, MK5, MK22> CMC6, KCY 250/5, KC5, NBob; MBHO MBP603/KA200N, AT 3031, DPA 4061 w/ d:vice, Naiant X-X, AT 853c, shotgun, Nak300
Pres/Power: Aerco MP2, tinybox v2  [KCY], CA-UBB
Decks: Sound Devices MixPre 6, Zoom F8, M10, D50

My recordings on nyctaper.com: http://www.nyctaper.com/?tag=acidjack | LMA: http://www.archive.org/bookmarks/acidjack | twitter: http://www.twitter.com/acidjacknyc | Soundcloud: https://soundcloud.com/acidjacknyc

Offline dactylus

  • Site Supporter
  • Trade Count: (62)
  • Needs to get out more...
  • *
  • Posts: 5992
  • Gender: Male
  • Maplewood, MN
Re: My SRS 3D printed microphone bars
« Reply #8 on: July 31, 2017, 12:28:17 PM »

I'm going to run mk22 and mk41v pairs on that bar along with a mk4v/mk8 M/S rig on Sunday at Phish

It will be interesting to hear the mk4v/mk8 M/S rig in action.  Have a good time this evening!


Noah did you decide to run the mk4v/mk8 M/S rig at a future show?

hot licks > microphones > recorder



...ball of confusion, that's what the world is today, hey hey...

Offline noahbickart

  • phishrabbi
  • Site Supporter
  • Trade Count: (33)
  • Needs to get out more...
  • *
  • Posts: 2554
  • Gender: Male
  • So now I wander over grounds of light...
Re: My SRS 3D printed microphone bars
« Reply #9 on: July 31, 2017, 12:47:19 PM »

I'm going to run mk22 and mk41v pairs on that bar along with a mk4v/mk8 M/S rig on Sunday at Phish

It will be interesting to hear the mk4v/mk8 M/S rig in action.  Have a good time this evening!


Noah did you decide to run the mk4v/mk8 M/S rig at a future show?

I ran the 4v pair again last night. The bar was heavy enough and I didn't feel like doing an extra clamp and mount for m/s. Sorry
Recording:
Capsules: Schoeps mk41v (x2), mk22 (x2), mk3 (x2), mk21 & mk8
Cables: 2x nbob KCY, 1 pair nbob actives, GAKables 10' & 20' 6-channel snakes, Darktrain 2 & 4 channel KCY and mini xlr extensions:
Preamps:    Schoeps VMS 02iub, Naiant IPA, Sound Devices Mixpre6 I
Recorders: Sound Devices Mixpre6 I, Sony PCM m10

Home Playback: Mac Mini> Mytek Brooklyn+> McIntosh MC162> Eminent Tech LFT-16; Musical Fidelity xCan v2> Hifiman HE-4XX / Beyerdynamic DT880

Office Playback: iMac> Grace m903> AKG k701 / Hifiman HE-400

Offline fobstl

  • Trade Count: (4)
  • Taperssection All-Star
  • ****
  • Posts: 1629
Re: My SRS 3D printed microphone bars
« Reply #10 on: July 31, 2017, 01:54:49 PM »
The bars that Scott is creating are truly awesome. I currently have him working on a Kangol mount that looks like it is going to be pretty cool.

Could you please remember to post that when it's done? Or if there's a place to buy one now, I'd love a link...
Yes, Scott is sending me his second prototype to review. Once we have it finalized I will let everyone know.

Offline dactylus

  • Site Supporter
  • Trade Count: (62)
  • Needs to get out more...
  • *
  • Posts: 5992
  • Gender: Male
  • Maplewood, MN
Re: My SRS 3D printed microphone bars
« Reply #11 on: August 03, 2017, 12:32:17 PM »

I'm going to run mk22 and mk41v pairs on that bar along with a mk4v/mk8 M/S rig on Sunday at Phish

It will be interesting to hear the mk4v/mk8 M/S rig in action.  Have a good time this evening!


Noah did you decide to run the mk4v/mk8 M/S rig at a future show?

I ran the 4v pair again last night. The bar was heavy enough and I didn't feel like doing an extra clamp and mount for m/s. Sorry

Thanks Noah!  I understand completely.  Do you have any recordings posted using your mk4v/mk8 M/S rig?  I'd love to hear how that setup sounds.

hot licks > microphones > recorder



...ball of confusion, that's what the world is today, hey hey...

Offline F.O.Bean

  • Team Schoeps Tapir that
  • Trade Count: (126)
  • Needs to get out more...
  • *****
  • Posts: 40690
  • Gender: Male
  • Taperus Maximus
    • MediaFire Recordings
Re: My SRS 3D printed microphone bars
« Reply #12 on: August 03, 2017, 03:48:39 PM »
Here's the [3] SRS 4 Channel Mounts that I have too! I HIGHLY recommend these to ANYONE who wants to run 2+ Channels and do it very lightweight ;) ALL of my capsules are VERTICALLY ALIGNED, and because of that, I can easily mix the multi mic configs for a 4 Channel Matrix, IF the tapes came out good enough :)

DINa/DIN
https://www.shapeways.com/product/J5WZFJ324/dina-din-combo?optionId=60350415

DINa/ORTF
https://www.shapeways.com/product/EARVGAFW3/dina-ortf-combo?li=shareProduct

DINa/NOS
https://www.shapeways.com/product/DU5BBY7BA/dina-nos-combo?optionId=60421670

And Noah, thanks for all of your hard work @MSG ;) ;D
Schoeps MK 4V & MK 41V ->
Schoeps 250|0 KCY's (x2) ->
Naiant +60v|Low Noise PFA's (x2) ->
DarkTrain Right Angle Stubby XLR's (x3) ->
Sound Devices MixPre-6 & MixPre-3

http://www.archive.org/bookmarks/diskobean
http://www.archive.org/bookmarks/Bean420
http://bt.etree.org/mytorrents.php
http://www.mediafire.com/folder/j9eu80jpuaubz/Recordings

Offline noahbickart

  • phishrabbi
  • Site Supporter
  • Trade Count: (33)
  • Needs to get out more...
  • *
  • Posts: 2554
  • Gender: Male
  • So now I wander over grounds of light...
Re: My SRS 3D printed microphone bars
« Reply #13 on: August 24, 2017, 08:05:21 AM »
Bean:

I really encourage you to experiment with narrower angles and wider spacings. Your bars are all 110 or 90 degrees, which work great for FOB on on stage, but from the OTS, there's too little direct sound compared with too much reflected sound and crowd noise.

Here's the [3] SRS 4 Channel Mounts that I have too! I HIGHLY recommend these to ANYONE who wants to run 2+ Channels and do it very lightweight ;) ALL of my capsules are VERTICALLY ALIGNED, and because of that, I can easily mix the multi mic configs for a 4 Channel Matrix, IF the tapes came out good enough :)

DINa/DIN
https://www.shapeways.com/product/J5WZFJ324/dina-din-combo?optionId=60350415

DINa/ORTF
https://www.shapeways.com/product/EARVGAFW3/dina-ortf-combo?li=shareProduct

DINa/NOS
https://www.shapeways.com/product/DU5BBY7BA/dina-nos-combo?optionId=60421670

And Noah, thanks for all of your hard work @MSG ;) ;D
Recording:
Capsules: Schoeps mk41v (x2), mk22 (x2), mk3 (x2), mk21 & mk8
Cables: 2x nbob KCY, 1 pair nbob actives, GAKables 10' & 20' 6-channel snakes, Darktrain 2 & 4 channel KCY and mini xlr extensions:
Preamps:    Schoeps VMS 02iub, Naiant IPA, Sound Devices Mixpre6 I
Recorders: Sound Devices Mixpre6 I, Sony PCM m10

Home Playback: Mac Mini> Mytek Brooklyn+> McIntosh MC162> Eminent Tech LFT-16; Musical Fidelity xCan v2> Hifiman HE-4XX / Beyerdynamic DT880

Office Playback: iMac> Grace m903> AKG k701 / Hifiman HE-400

Offline noahbickart

  • phishrabbi
  • Site Supporter
  • Trade Count: (33)
  • Needs to get out more...
  • *
  • Posts: 2554
  • Gender: Male
  • So now I wander over grounds of light...
Re: My SRS 3D printed microphone bars
« Reply #14 on: August 31, 2017, 10:07:42 PM »

Nice bars Noah!  I think that I'm going to pick up the newest bar that you posted for my mk22's & mk4V's.

That bar was designed for the mk41v but would likely work with the 4v as well.

I'm going to run mk22 and mk41v pairs on that bar along with a mk4v/mk8 M/S rig on Sunday at Phish

Yes, I saw that you had the bar constructed for mk41v's but it should also be effective for the mk4v's that I run.

 :coolguy:

I used the mk4v in this mount along with the mk22. Check them out:

mk22 16bit: http://bt.etree.org/details.php?id=594985
mk22 24bit: http://bt.etree.org/details.php?id=595004

mk4v 16bit: http://bt.etree.org/details.php?id=595006
mk4v 24bit: http://bt.etree.org/details.php?id=595005
Recording:
Capsules: Schoeps mk41v (x2), mk22 (x2), mk3 (x2), mk21 & mk8
Cables: 2x nbob KCY, 1 pair nbob actives, GAKables 10' & 20' 6-channel snakes, Darktrain 2 & 4 channel KCY and mini xlr extensions:
Preamps:    Schoeps VMS 02iub, Naiant IPA, Sound Devices Mixpre6 I
Recorders: Sound Devices Mixpre6 I, Sony PCM m10

Home Playback: Mac Mini> Mytek Brooklyn+> McIntosh MC162> Eminent Tech LFT-16; Musical Fidelity xCan v2> Hifiman HE-4XX / Beyerdynamic DT880

Office Playback: iMac> Grace m903> AKG k701 / Hifiman HE-400

 

RSS | Mobile
Page created in 0.09 seconds with 44 queries.
© 2002-2024 Taperssection.com
Powered by SMF