Become a Site Supporter and Never see Ads again!

Author Topic: Thoughts on ACM V3  (Read 21217 times)

0 Members and 1 Guest are viewing this topic.

Offline sygdwm

  • unknown sleath taper
  • Trade Count: (1)
  • Needs to get out more...
  • *****
  • Posts: 8747
  • Gender: Male
Re: Thoughts on ACM V3
« Reply #60 on: October 08, 2008, 03:46:26 PM »
if you turn on hpf at wsp, you are dead to me.

/2
mics: (4)akg c460b(a60,mk46,ck1x,ck1,ck2,ck3,ck61,ck63)
pres: oade m148/edirol wmod ua5
recorders: marantz stock671/oade acm671/fostex busman vintage fr2le

(P.S.: On a threaded discussion board like this one, there's no need to repeat someone's post when you reply to them; everyone can see all the messages in the thread.)

Offline Kevin Straker

  • The Shogun of Easley
  • Trade Count: (4)
  • Needs to get out more...
  • *****
  • Posts: 2310
  • Gender: Male
Re: Thoughts on ACM V3
« Reply #61 on: October 08, 2008, 04:22:47 PM »
if you turn on hpf at wsp, you are dead to me.

/2
;D Usually I'd agree, but with the ACM you'll be screwed if you don't use it. IMO
I'd use the hpf2. I think it's the one for the super low freq.
People on ludes should not drive...
J. Spicoli

mk4,mk21>kc5>cmc6>V3>SD722

Offline OFOTD

  • Amorican
  • Trade Count: (7)
  • Needs to get out more...
  • *****
  • Posts: 6307
Re: Thoughts on ACM V3
« Reply #62 on: October 08, 2008, 04:43:47 PM »
if you turn on hpf at wsp, you are dead to me.

/2
;D Usually I'd agree, but with the ACM you'll be screwed if you don't use it. IMO
I'd use the hpf2. I think it's the one for the super low freq.

I have to agree that the bass smacks you in the face pretty hard with the ACM mod.  I typically will roll off anywhere from 50Hz - 90Hz in post.  While I think it probably would save me a bunch of time if I did it on the fly I like being able to set exactly how much roll off to use as well as how steep that roll off should be.

Depending on your internal jumpers position in the V3  #2 is always the lower frequencies (either 50Hz or 75Hz) the #1 position is (100Hz or 125Hz respectively)  I think by default that the V3 using the low settings:

1: 100Hz
2: 50Hz


Offline L Ron Hoover

  • Trade Count: (0)
  • Needs to get out more...
  • *****
  • Posts: 2233
  • "I figure the odds be 50/50"
Re: Thoughts on ACM V3
« Reply #63 on: October 08, 2008, 07:23:43 PM »
I'm really digging mine with the Gefell M300's. Thanks again Kevin.

Offline orechall

  • Team Bama
  • Trade Count: (7)
  • Needs to get out more...
  • *****
  • Posts: 2934
  • Gender: Male
Re: Thoughts on ACM V3
« Reply #64 on: October 09, 2008, 10:01:33 AM »
I have never run the hpf on the acm v3....even taping panic...there is no need for it. 
DPA 4023's & 4028's->Lunatec V2 /Lunatec ACM V3/Sonosax SX-M2/AETA PSP-3(x2)

Hi-Ho Silver Cables and Interconnects

Offline Kevin Straker

  • The Shogun of Easley
  • Trade Count: (4)
  • Needs to get out more...
  • *****
  • Posts: 2310
  • Gender: Male
Re: Thoughts on ACM V3
« Reply #65 on: October 09, 2008, 01:11:19 PM »
I have never run the hpf on the acm v3....even taping panic...there is no need for it. 

Not if you're going to do roll off in post. :P Every show I did with my ACM sounded bloated with mk4's. They sounded much better with 80hz rolloff.
People on ludes should not drive...
J. Spicoli

mk4,mk21>kc5>cmc6>V3>SD722

Offline OFOTD

  • Amorican
  • Trade Count: (7)
  • Needs to get out more...
  • *****
  • Posts: 6307
Re: Thoughts on ACM V3
« Reply #66 on: October 09, 2008, 01:59:16 PM »
Well in Chris' defense running the ACM V3 with the DPA's really doesn't have the same effect as the Schoeps and Neumann's do   With the Schoeps/Neumann's you do get that bloated sense of bass.  Overpowering alot of times.   With the 402x's the bass is there but it is super tight and  more focused.  I've found that I rarely need to EQ the recording since I sold the 140's and bought the 4021's.

I'm taping Panic tomorrow and Saturday in Austin and ill seed the 4021 > ACM V3 Friday source without any EQ'ing other than volume adjustments.  We'll see how the bass sounds.


Offline dactylus

  • Site Supporter
  • Trade Count: (62)
  • Needs to get out more...
  • *
  • Posts: 5992
  • Gender: Male
  • Maplewood, MN
Re: Thoughts on ACM V3
« Reply #67 on: October 09, 2008, 04:58:23 PM »
I have never run the hpf on the acm v3....even taping panic...there is no need for it. 

Can any gefell users chime in?  I have yet to run the acm v3 with the gefells...  Hopefully I'll be running it for The Black Crowes on Halloween!!

 :)
« Last Edit: October 09, 2008, 05:02:21 PM by dactylus »
hot licks > microphones > recorder



...ball of confusion, that's what the world is today, hey hey...

Offline SmokinJoe

  • Trade Count: (63)
  • Needs to get out more...
  • *****
  • Posts: 4210
  • Gender: Male
  • "75 and sunny"... life is so much simpler.
    • uploads to archive.org
Re: Thoughts on ACM V3
« Reply #68 on: October 10, 2008, 08:43:29 PM »
Anyone got one of these in the North East?

I'm thinking about sending mine out for mod... the Earthworks can use some bottom end, but I'd really like to try it out before committing.

I was hoping if someone has one, and will be at a show I will be at, maybe we can swap for the opening act or for the evening.

Thanks,
Joe
Mics: Schoeps MK4 & CMC5's / Gefell M200's & M210's / ADK-TL / DPA4061's
Pres: V3 / ST9100
Decks: Oade Concert Mod R4Pro / R09 / R05
Photo: Nikon D700's, 2.8 Zooms, and Zeiss primes
Playback: Raspberry Pi > Modi2 Uber > Magni2 > HD650

Offline orechall

  • Team Bama
  • Trade Count: (7)
  • Needs to get out more...
  • *****
  • Posts: 2934
  • Gender: Male
Re: Thoughts on ACM V3
« Reply #69 on: October 10, 2008, 08:59:29 PM »
Joe,

I am convinced the mod is the way to go with the mics I use I know it probably will be different with different mics but I will tell you this...I got a busy month but when I get back in town from new orleans after halloween I could ship you mine for you to try out. I have a fairly busy november as well but I am sure we could work something out.  no need in getting the mod if it doesnt work with your mics...shoot me a pm at some point and we can work it out.

Chris
DPA 4023's & 4028's->Lunatec V2 /Lunatec ACM V3/Sonosax SX-M2/AETA PSP-3(x2)

Hi-Ho Silver Cables and Interconnects

Offline SmokinJoe

  • Trade Count: (63)
  • Needs to get out more...
  • *****
  • Posts: 4210
  • Gender: Male
  • "75 and sunny"... life is so much simpler.
    • uploads to archive.org
Re: Thoughts on ACM V3
« Reply #70 on: October 11, 2008, 07:58:41 AM »
I really appreciate the offer Chris.  I'll wait a little while to see if one pops up locally, but if not I may take you up on your offer.
Mics: Schoeps MK4 & CMC5's / Gefell M200's & M210's / ADK-TL / DPA4061's
Pres: V3 / ST9100
Decks: Oade Concert Mod R4Pro / R09 / R05
Photo: Nikon D700's, 2.8 Zooms, and Zeiss primes
Playback: Raspberry Pi > Modi2 Uber > Magni2 > HD650

Offline dactylus

  • Site Supporter
  • Trade Count: (62)
  • Needs to get out more...
  • *
  • Posts: 5992
  • Gender: Male
  • Maplewood, MN
Re: Thoughts on ACM V3
« Reply #71 on: October 11, 2008, 08:36:01 AM »
I have never run the hpf on the acm v3....even taping panic...there is no need for it. 

Not if you're going to do roll off in post. :P Every show I did with my ACM sounded bloated with mk4's. They sounded much better with 80hz rolloff.


I'm looking for a ballpark figure - how much 80hz rolloff did you use for your various recordings?
I don't have much experience in the bass rolloff area and would like a probable starting point if I need it for the Gefell mics.  Thank you!


 :hmmm:

hot licks > microphones > recorder



...ball of confusion, that's what the world is today, hey hey...

spreadheadtom

  • Guest
  • Trade Count: (0)
Re: Thoughts on ACM V3
« Reply #72 on: October 16, 2008, 11:00:15 AM »
my thoughts after running it last night for the first time......in your face!

wsp....bowlegged woman (mp3)...http://www.mediafire.com/?zmzezhgx2mk

Offline OFOTD

  • Amorican
  • Trade Count: (7)
  • Needs to get out more...
  • *****
  • Posts: 6307
Re: Thoughts on ACM V3
« Reply #73 on: October 16, 2008, 11:45:36 AM »
my thoughts after running it last night for the first time......in your face!

wsp....bowlegged woman (mp3)...http://www.mediafire.com/?zmzezhgx2mk

I'm guessing anytime you get a LG&$ it's a good night.    >:D

Grabbing your torrent now.

Thanks Tommy.

 

stirinthesauce

  • Guest
  • Trade Count: (0)
Re: Thoughts on ACM V3
« Reply #74 on: October 24, 2008, 12:23:23 AM »
Tommy, sounds very nice.  I dig these Senns

 

RSS | Mobile
Page created in 0.118 seconds with 43 queries.
© 2002-2024 Taperssection.com
Powered by SMF