Become a Site Supporter and Never see Ads again!

Author Topic: my Naiant preamp arrived  (Read 8910 times)

0 Members and 1 Guest are viewing this topic.

Offline Church-Audio

  • Trade Count: (44)
  • Needs to get out more...
  • *****
  • Posts: 7571
  • Gender: Male
Re: my Naiant preamp arrived
« Reply #15 on: September 10, 2008, 10:00:18 AM »
I'm very curious about your setup as well as I am in the market for a small, portable preamp and am leaning towards the Naiant unit.

Please share your results...

If you have a little patience, 5 Fish's TS-2 preamp might be available soon.

No offence but this thread is about Niant and not FF. I dont think its cool to flog FF in a Niant thread. Just like it would not be cool to flog Niant in a FF thread...Just a bit of advice.

Chris




No "offence" CC, but he didn't flog FF's pre project, he touted it in the quoted post.  The worst thing the man is guilty of is a nOOb mistake if indeed there even is one.  Plenty of OT stuff gets posted that doesn't raise an eyebrow.   ::)

I think I used the wrong words.. But anyway he was very cool about it and all is good. I really was not going to say anything. I dont know what OT is though :)
for warranty returns email me at
EMAIL Sales@church-audio.com

Offline Krispy D

  • Trade Count: (1)
  • Needs to get out more...
  • *****
  • Posts: 4878
  • Gender: Male
    • my recordings on LMA
Re: my Naiant preamp arrived
« Reply #16 on: September 10, 2008, 10:16:08 AM »
off topic?
Peluso CEMC6, ck4/ck21
Oktava MC012
Sony ECM260f
AT 811

canare star quads
DIY mil spec silvers

DIY (W-ish) mod UA5>JB3
Oade ACM PMD 660
R4


You cannot strengthen the weak by weakening the strong. You cannot help the wage-earner by pulling down the wage-payer. You cannot help the poor by destroying the rich. You cannot help men permanently by doing for them what they could and should do for themselves.
~Rev. William J. H. Boetcker (not Lincoln)

Offline Church-Audio

  • Trade Count: (44)
  • Needs to get out more...
  • *****
  • Posts: 7571
  • Gender: Male
Re: my Naiant preamp arrived
« Reply #17 on: September 10, 2008, 10:22:40 AM »
off topic?

Output transformer, Over Time, Original Taper? I am not sure I guess I am just not hip enough to know what all these fancy terms are nowadays.
for warranty returns email me at
EMAIL Sales@church-audio.com

Offline Krispy D

  • Trade Count: (1)
  • Needs to get out more...
  • *****
  • Posts: 4878
  • Gender: Male
    • my recordings on LMA
Re: my Naiant preamp arrived
« Reply #18 on: September 10, 2008, 10:31:21 AM »
mine wasn't just a guess, it was based on contextual information....   ;) 

Pretty sure that "Plenty of Output Transformer stuff gets posted that doesn't raise an eyebrow" isn't exactly what the post was meant to read.
Peluso CEMC6, ck4/ck21
Oktava MC012
Sony ECM260f
AT 811

canare star quads
DIY mil spec silvers

DIY (W-ish) mod UA5>JB3
Oade ACM PMD 660
R4


You cannot strengthen the weak by weakening the strong. You cannot help the wage-earner by pulling down the wage-payer. You cannot help the poor by destroying the rich. You cannot help men permanently by doing for them what they could and should do for themselves.
~Rev. William J. H. Boetcker (not Lincoln)

Offline Krispy D

  • Trade Count: (1)
  • Needs to get out more...
  • *****
  • Posts: 4878
  • Gender: Male
    • my recordings on LMA
Re: my Naiant preamp arrived
« Reply #19 on: September 11, 2008, 10:12:18 AM »
Krispy D; proof that education isn't wasted on the young.  ;)

I'm not getting any prettier, might as well get smarter...
Peluso CEMC6, ck4/ck21
Oktava MC012
Sony ECM260f
AT 811

canare star quads
DIY mil spec silvers

DIY (W-ish) mod UA5>JB3
Oade ACM PMD 660
R4


You cannot strengthen the weak by weakening the strong. You cannot help the wage-earner by pulling down the wage-payer. You cannot help the poor by destroying the rich. You cannot help men permanently by doing for them what they could and should do for themselves.
~Rev. William J. H. Boetcker (not Lincoln)

 

RSS | Mobile
Page created in 0.088 seconds with 33 queries.
© 2002-2024 Taperssection.com
Powered by SMF