Soldering is a method of joining metal parts using a filler metal of low (The temperature below which a liquid turns into a solid) melting point ( (An alloy (usually of lead and tin) used when melted to join two metal surfaces) solder). Heat is applied to the metal parts, and the soft filler metal is pressed against the joint, melts, and is drawn into the joint by (A phenomenon associated with surface tension and resulting in the elevation or depression of liquids in capillaries) capillary action. After the metal cools, the resulting joints are not as strong as the base metal, but have adequate strength, electrical conductivity, and water-tightness for many uses. Soldering is an ancient technique that has been used practically as long as humans have been making articles out of metal.
Soldering can be done in a number of ways, including passing parts over a bulk container of melted solder, using an (The infrared part of the electromagnetic spectrum; electromagnetic wave frequencies below the visible range) infrared lamp, or by using a point source such as an (A car that is powered by electricity) electric (A hand tool with a heatable tip; used to melt and apply solder) soldering iron or (Click link for more info and facts about brazing) brazing torch. A (The rate of flow of energy or particles across a given surface) flux is usually used to assist in the joining process. This flux can be manufactured as part of the solder in a so called 'multicore' solder.
One application of soldering is making connections between electronic parts and printed circuit boards. Another is in (The occupation of a plumber (installing and repairing pipes and fixtures for water or gas or sewage in a building)) plumbing. Joints in sheet-metal objects such as cans for food, roof flashing, and drain gutters were also traditionally soldered. Jewellry and small mechanical parts are often assembled by soldering. Soldering can also be used as a repair techniqe to patch a leak in a container or cooking vessel.
Soldering is distinct from (Fastening two pieces of metal together by softening with heat and applying pressure) welding in that the base materials to be joined are not melted. The lower melting point solder can be melted away leaving the original materials intact. Brazing is similar to soldering but uses higher melting temperature alloys, based on copper, as the filler metal.
Since (A soft heavy toxic malleable metallic element; bluish white when freshly cut but tarnishes readily to dull gray) lead used in traditional solder alloys is toxic, much effort in industry has been directed to adapting soldering techniques to use lead-free alloys for assembly of electronic devices and for potable water supply piping.
Basic electronic soldering techniques
All solder pads and device terminals must be clean for good (The act of making something wet) wetting. The soldering iron or gun must be clean, otherwise components may heat up excessively. The devices must be mounted on the (A printed circuit that can be inserted into expansion slots in a computer to increase the computer's capabilities) circuit board properly. One technique is to elevate the components from the board surface (a few millimeters) to prevent heating of circuit board. After device insertion, the excess leads can be cut leaving only a length equal to the radius of the pad. You may use plastic mounting clips or holders for large devices to reduce mounting stresses.
Heat sink the leads of sensitive devices to prevent heat damage. Apply soldering iron or gun to both terminal lead and copper pad to equally heat both. Apply solder to both lead and pad but never directly to the tip of soldering iron or gun. Direct contact will cause the molten solder to flow over the gun and not over the joint. The moment the solder melts and begins to flow, remove the solder supply immediately. Do not remove the iron yet. The remaining solder will then flow over the junction of the lead and pad, assuming both are free of dirt.Let the iron heat the molten solder for a few seconds. This will let the excess flux vaporize. Remove the iron from the junction and let the junction cool.
Be sure not move the joint while it is cooling. Doing so will result in a fractured joint. Do not blow air onto the joint while it is cooling. Instead, let it cool naturally. A good solder joint is smooth and shiny. The lead outline should be clearly visible. Clean the soldering iron tip before you begin on a new joint. It is absolutely important that the iron tip be free of residual flux and solder. After you finish all of the joints, remove excess flux residue from the board using alcohol, acetone, or other organic solvent.
Stained Glass Soldering
Historically soldering tips were copper, placed in braziers. One tip was used, when the heat had transfered from the tip to the solder (and depleted the heat reserve) it was placed back in the brazier of charcoal and the next tip was used.
Currently, electric soldering irons are used, they consist of coil or cermaic heating elements, which retain heat differently, and warm up the mass differently, internal or external rheostats, and different power ratings - which change how long a bead can be run.
Common solders for stained glass are mixtures of tin and lead, respectively:
60/40: melts between 361°-376°F
50/50: melts between 368°-421°F
63/37: melts between 355°-365°F
lead-free solder (useful in jewelry, eating containers, and other environemental uses): melts around 490°F
Pipe/Mechanical Soldering
Sometimes it is necessary to use solders of different melting points in complex jobs.
Soldering defects
Soldering defects are solder joints that are not soldered correctly. These defects may arise when solder temperature is too low. When the solder is too cold, it will not flow and will "ball up". An incorrect solder type (for example, electronics solder for mechanical joints or vice versa) may lead to a weak joint. An incorrect or missing flux can corrode the metals in the joint. Without flux the joint may not be clean. A dirty or contaminated joint usually leads to a weak bond. A lack of solder on a joint will make the joint prone to failure. An excess of solder can create "solder bridges" which create short circuits. Movement of metals being soldered before the solder has cooled will make the solder appear grainy and may occur as a weakened joint.
Soldering defects in elecronics can lead to short circuits, high resistance in the joint, intermittent connections, components overheating, and damaged circuit boards. In mechanical joints defects can lead to joint failure and corrosion.
I once constructed a fully functional hobby horse using solder and broomstraw.I miss that ugly metal and straw monstrosity more than I miss my own dear mother. Cursed life of agony!Wretched fate that swoops in on broken glass talons and steals the hearts and minds of the people!!Damn you to hell fate! I defy your logic and forked tongue!
-Cliff
Topic: how to solder dpa 4061 (Read 6468 times)