Become a Site Supporter and Never see Ads again!

Author Topic: m248 vs. V3 ACM  (Read 1471 times)

0 Members and 1 Guest are viewing this topic.

Offline rasta

  • Trade Count: (1)
  • Taperssection Member
  • ***
  • Posts: 279
  • Gender: Male
m248 vs. V3 ACM
« on: October 14, 2007, 07:20:11 PM »
opinions on the 2?
4023>m148>722

Offline OFOTD

  • Amorican
  • Trade Count: (7)
  • Needs to get out more...
  • *****
  • Posts: 6310
Re: m248 vs. V3 ACM
« Reply #1 on: October 14, 2007, 10:11:17 PM »
opinions on the 2?

First and foremost the 248 is a preamp only.   So you may want to ask the question a little different.  V3 pre vs. m248. 

As far as the a/d section in the ACM V3 vs. the 722 you have  No contest.  The ACM V3 a/d section runs circles around the 722 a/d. 

Of the differences between the 248 and V3 pres there are tons of threads here with people's opinions.  Alot also depends on what mics you're using.

Offline rasta

  • Trade Count: (1)
  • Taperssection Member
  • ***
  • Posts: 279
  • Gender: Male
Re: m248 vs. V3 ACM
« Reply #2 on: October 15, 2007, 04:26:59 PM »
opinions on the 2?

First and foremost the 248 is a preamp only.   So you may want to ask the question a little different.  V3 pre vs. m248. 

As far as the a/d section in the ACM V3 vs. the 722 you have  No contest.  The ACM V3 a/d section runs circles around the 722 a/d. 

Of the differences between the 248 and V3 pres there are tons of threads here with people's opinions.  Alot also depends on what mics you're using.
Thank you.  I didn't make it clear that I would like to still use the 722 A/D.
4023>m148>722

Offline Wiggler

  • Trade Count: (0)
  • Taperssection All-Star
  • ****
  • Posts: 1315
  • Gender: Male
Re: m248 vs. V3 ACM
« Reply #3 on: October 15, 2007, 04:59:34 PM »
My understanding is that the ACM Doug does to the V3 only affects the A/D stage of the unit.
If you are going to use the 722s A/D a stock V3 should be just as affective.
See this thread pretaining to the V3 ACM.
http://taperssection.com/index.php/topic,79244.0.html

Offline rasta

  • Trade Count: (1)
  • Taperssection Member
  • ***
  • Posts: 279
  • Gender: Male
Re: m248 vs. V3 ACM
« Reply #4 on: October 15, 2007, 07:22:37 PM »
My understanding is that the ACM Doug does to the V3 only affects the A/D stage of the unit.
If you are going to use the 722s A/D a stock V3 should be just as affective.
See this thread pretaining to the V3 ACM.
http://taperssection.com/index.php/topic,79244.0.html
Thanks for that clarification.
+T everyone
4023>m148>722

 

RSS | Mobile
Page created in 0.091 seconds with 46 queries.
© 2002-2020 Taperssection.com
Powered by SMF