Become a Site Supporter and Never see Ads again!

Author Topic: yet another mx 100 question....  (Read 1332 times)

0 Members and 1 Guest are viewing this topic.

Offline heyitsmejess

  • Trade Count: (2)
  • Taperssection All-Star
  • ****
  • Posts: 1208
  • Gender: Male
yet another mx 100 question....
« on: December 01, 2007, 06:08:06 PM »
i attempted to wire my recently purchased mx 100 to run on 2 9v batteries, using this diagram.



it didnt work.

my question is this.  when looking at the diagram, is this showing the power-in from the outside of the box, or the inside of the box?

thanks again TS for helping with my many questions!
cause we zig and zag between good and bad
stumble and fall on right and wrong


http://www.rumpkemountainboys.org/

Offline flipp

  • resident curmudgeon
  • Trade Count: (17)
  • Needs to get out more...
  • *****
  • Posts: 4308
Re: yet another mx 100 question....
« Reply #1 on: December 01, 2007, 06:33:41 PM »
according to the rectangle in the bottom left of the diagram, that's inside the box

let me take the cover off mine and I'll see if I can confirm


<edit: That is the way the connector would look if you have the cover off and are looking from the level pots across the circuit board to the back side of the power connector. It should have a red wire connected to it. Counter clockwise from the 6 oclock position, red(4), blue(3), yellow(2), black(1). >
« Last Edit: December 01, 2007, 06:58:49 PM by flipp »

Offline heyitsmejess

  • Trade Count: (2)
  • Taperssection All-Star
  • ****
  • Posts: 1208
  • Gender: Male
Re: yet another mx 100 question....
« Reply #2 on: December 01, 2007, 07:13:24 PM »
alright...no wonder it didnt work!  i have some more soldering to do!

thanks!
cause we zig and zag between good and bad
stumble and fall on right and wrong


http://www.rumpkemountainboys.org/

Offline heyitsmejess

  • Trade Count: (2)
  • Taperssection All-Star
  • ****
  • Posts: 1208
  • Gender: Male
Re: yet another mx 100 question....
« Reply #3 on: December 02, 2007, 12:17:57 PM »
well...that wasnt the culprit.

still not working.

anyone have any ideas?
cause we zig and zag between good and bad
stumble and fall on right and wrong


http://www.rumpkemountainboys.org/

Offline capnhook

  • All your llamas are belong to us....
  • Site Supporter
  • Trade Count: (20)
  • Needs to get out more...
  • *
  • Posts: 4013
  • All your llamas are belong to us....
Re: yet another mx 100 question....
« Reply #4 on: December 02, 2007, 08:11:31 PM »

See my post in the NAK team section.......

Kevin
Proud member of the reality-based community

BSCS-L->JB-mod [NAK CM-300 (CP-3) and/or (CP-1)]->LSD2->CA CAFS-Omni->Sony ECM-907**Apogee MiniMe Rev. C->CA Ugly II->**Edirol OCM R-44->Tascam DR-22WL->Sony TCD-D8


"Don't ever take an all or nothing attitude when it comes to making a difference
and being beautiful and making the world a beautiful place through your actions.
Every little bit is registered.  Every little bit.  So be as beautiful as you can as often as you can"

"It'll never be over, 'till we learn."
 
"My dream is to get a bus and get the band and just go coast to coast. Just about everything else except music, is anti-musical.  That's it.  Music's the thing." - Jeb Puryear

 

RSS | Mobile
Page created in 0.087 seconds with 46 queries.
© 2002-2020 Taperssection.com
Powered by SMF