Become a Site Supporter and Never see Ads again!

Author Topic: Rubber end sleaves for AA Batteries ?  (Read 2602 times)

0 Members and 1 Guest are viewing this topic.

Offline gdplusmore

  • Trade Count: (2)
  • Taperssection Regular
  • **
  • Posts: 174
  • Gender: Male
Rubber end sleaves for AA Batteries ?
« on: January 27, 2009, 03:10:53 PM »
anyone know of  a source where I purchase rubber end sleaves for AA Batteries...these are needed when placing the Battery into my
nak 100 bodies...

Thanks
NAK CM-300's  -> CP4's,CP-3's,CP2's,CP1's ->SonyD5
NAKCM-300's ->  CP4's,CP-3's,CP2's,CP1's ->MX-100-->NJB3
NAK CM-100's  -> CP4's,CP-3's,CP2's,CP1's ->SonyD5
NAKCM-100's ->  CP4's,CP-3's,CP2's,CP1's ->MX-100-->NJB3
Sony PCM-M10  (looking at stealth mic options)

Offline flipp

  • resident curmudgeon
  • Trade Count: (17)
  • Needs to get out more...
  • *****
  • Posts: 4285
Re: Rubber end sleaves for AA Batteries ?
« Reply #1 on: January 27, 2009, 03:56:24 PM »
have never found a direct replacement but I took a mic and a battery to my local home center and found some o-rings that made acceptable substitutes

Offline gdplusmore

  • Trade Count: (2)
  • Taperssection Regular
  • **
  • Posts: 174
  • Gender: Male
Re: Rubber end sleaves for AA Batteries ?
« Reply #2 on: January 27, 2009, 04:08:24 PM »
thanks for the suggestion
NAK CM-300's  -> CP4's,CP-3's,CP2's,CP1's ->SonyD5
NAKCM-300's ->  CP4's,CP-3's,CP2's,CP1's ->MX-100-->NJB3
NAK CM-100's  -> CP4's,CP-3's,CP2's,CP1's ->SonyD5
NAKCM-100's ->  CP4's,CP-3's,CP2's,CP1's ->MX-100-->NJB3
Sony PCM-M10  (looking at stealth mic options)

Offline neutrino

  • Trade Count: (1)
  • Taperssection Member
  • ***
  • Posts: 615
  • Gender: Male
  • **Team Chicago**
Re: Rubber end sleaves for AA Batteries ?
« Reply #3 on: January 27, 2009, 05:31:47 PM »
Wouldn't large heatshrink work? Or am I not getting the purpose of these sleeves..
CA14/OM14 > A10
Sony SBM-1 Oade mod

Offline gdplusmore

  • Trade Count: (2)
  • Taperssection Regular
  • **
  • Posts: 174
  • Gender: Male
Re: Rubber end sleaves for AA Batteries ?
« Reply #4 on: January 27, 2009, 07:12:14 PM »
heat shrink might work...just need something to keep the batteries snug in the body...and could go on and off the battery easily
NAK CM-300's  -> CP4's,CP-3's,CP2's,CP1's ->SonyD5
NAKCM-300's ->  CP4's,CP-3's,CP2's,CP1's ->MX-100-->NJB3
NAK CM-100's  -> CP4's,CP-3's,CP2's,CP1's ->SonyD5
NAKCM-100's ->  CP4's,CP-3's,CP2's,CP1's ->MX-100-->NJB3
Sony PCM-M10  (looking at stealth mic options)

Offline Lil Kim Jong-Il

  • Trade Count: (6)
  • Needs to get out more...
  • *****
  • Posts: 6498
  • large Marge sent me
Re: Rubber end sleaves for AA Batteries ?
« Reply #5 on: February 07, 2009, 10:13:38 AM »
Any reason why you need to get them on and off the batteries?

when I was running CM300s I wrapped tape around the batteries I used, adding layers of tape until the batteries were the diameter to fit the barrel.
The first rule of amateur neurosurgery club is .... I forget.

Offline gdplusmore

  • Trade Count: (2)
  • Taperssection Regular
  • **
  • Posts: 174
  • Gender: Male
Re: Rubber end sleaves for AA Batteries ?
« Reply #6 on: February 07, 2009, 02:37:05 PM »
the Nak100's take AA's after each show I remove the batteries from the barrels ,before the next show I replace the batteries with new ones and need to add the sleave to keep them snug...I do have some originals but that are starting to decay ....
NAK CM-300's  -> CP4's,CP-3's,CP2's,CP1's ->SonyD5
NAKCM-300's ->  CP4's,CP-3's,CP2's,CP1's ->MX-100-->NJB3
NAK CM-100's  -> CP4's,CP-3's,CP2's,CP1's ->SonyD5
NAKCM-100's ->  CP4's,CP-3's,CP2's,CP1's ->MX-100-->NJB3
Sony PCM-M10  (looking at stealth mic options)

Offline SmokinJoe

  • Trade Count: (63)
  • Needs to get out more...
  • *****
  • Posts: 4210
  • Gender: Male
  • "75 and sunny"... life is so much simpler.
    • uploads to archive.org
Re: Rubber end sleaves for AA Batteries ?
« Reply #7 on: February 08, 2009, 09:02:04 PM »
Go to hardware store or auto parts store with an AA battery and the mic body.  Look for something like plastic fuel line, rubber hose, maybe even PVC pipe... see if you can find something to fill the gap that will fit together loosely, but not too loosely.  As long as the battery is centered enough so it lines up with the contacts you are golden.
Mics: Schoeps MK4 & CMC5's / Gefell M200's & M210's / ADK-TL / DPA4061's
Pres: V3 / ST9100
Decks: Oade Concert Mod R4Pro / R09 / R05
Photo: Nikon D700's, 2.8 Zooms, and Zeiss primes
Playback: Raspberry Pi > Modi2 Uber > Magni2 > HD650

Offline gdplusmore

  • Trade Count: (2)
  • Taperssection Regular
  • **
  • Posts: 174
  • Gender: Male
Re: Rubber end sleaves for AA Batteries ?
« Reply #8 on: February 11, 2009, 07:50:22 PM »
thanks for the suggestion and glad to see you have some naks back in your bag... :)
NAK CM-300's  -> CP4's,CP-3's,CP2's,CP1's ->SonyD5
NAKCM-300's ->  CP4's,CP-3's,CP2's,CP1's ->MX-100-->NJB3
NAK CM-100's  -> CP4's,CP-3's,CP2's,CP1's ->SonyD5
NAKCM-100's ->  CP4's,CP-3's,CP2's,CP1's ->MX-100-->NJB3
Sony PCM-M10  (looking at stealth mic options)

 

RSS | Mobile
Page created in 0.051 seconds with 35 queries.
© 2002-2024 Taperssection.com
Powered by SMF