Become a Site Supporter and Never see Ads again!
« previous next »
Pages: 1 [2]  All   Go Down

Author Topic: PINECIL: Inexpensive and outstanding soldering iron with digital control  (Read 18061 times)

0 Members and 2 Guests are viewing this topic.

Offline Fried Chicken Boy

  • Trade Count: (8)
  • Needs to get out more...
  • *****
  • Posts: 3023
Re: PINECIL: Inexpensive and outstanding soldering iron with digital control
« Reply #15 on: February 21, 2022, 02:36:05 PM »
Marking thread.  I might have a use for an iron like this. 
Logged

Offline gormenghast

  • Trade Count: (44)
  • Taperssection Member
  • ***
  • Posts: 834
  • Gender: Male
Re: PINECIL: Inexpensive and outstanding soldering iron with digital control
« Reply #16 on: May 19, 2023, 07:51:09 PM »
Old thread I realize.  I have a Zune 120 that needs the battery replaced.  4 micro wires in a tight spot.  Will this solder iron do the job?   
Logged
A lot of people run a race to see who is the fastest. I run to see who has the most guts, who can punish himself into exhausting pace, and then at the end, punish himself even more.

Offline voltronic

  • Trade Count: (40)
  • Needs to get out more...
  • *****
  • Posts: 4185
Re: PINECIL: Inexpensive and outstanding soldering iron with digital control
« Reply #17 on: May 20, 2023, 07:23:37 AM »
Quote from: gormenghast on May 19, 2023, 07:51:09 PM
Old thread I realize.  I have a Zune 120 that needs the battery replaced.  4 micro wires in a tight spot.  Will this solder iron do the job?

The tightest spot I've used it in is TA5 connectors, which have tiny solder cups very close together. It did the job well.
Logged
I am hitting my head against the walls, but the walls are giving way.
- Gustav Mahler

Acoustic Recording Techniques
Team Classical
Team Line Audio
Team DPA

Offline audBall

  • Trade Count: (37)
  • Needs to get out more...
  • Posts: 6530
  • Gender: Male
  • Feel brand new about it
Re: PINECIL: Inexpensive and outstanding soldering iron with digital control
« Reply #18 on: May 23, 2023, 04:10:18 PM »
Has anyone powered theirs with DC? The Talentcell batteries (12V, 3A) seem like they would work based on the PINECIL specs. I'm just trying to avoid another wall plug/charger if possible.
Logged
mg m20.21.23 ■ akg ck61.62.63 »  nbob■naiant
aercomp2 ■ v2∞3 ■ sx-m2d2
pcm-d100 ■ pmd661 ■ r44ocm ■ f3

Offline SMsound

  • Trade Count: (0)
  • Taperssection Regular
  • **
  • Posts: 238
Re: PINECIL: Inexpensive and outstanding soldering iron with digital control
« Reply #19 on: May 23, 2023, 06:17:07 PM »
Quote from: audBall on May 23, 2023, 04:10:18 PM
Has anyone powered theirs with DC? The Talentcell batteries (12V, 3A) seem like they would work based on the PINECIL specs. I'm just trying to avoid another wall plug/charger if possible.

Data point for you: I sometimes use an 84w usbc block rather than 100w. This gets me slightly over 400°, not 450° which is still plenty.

I can prob try with dc in the next week or so.

Personally I have switched everything I can to usbc and wouldn't go back...
Logged
waves -> bits

Offline audBall

  • Trade Count: (37)
  • Needs to get out more...
  • Posts: 6530
  • Gender: Male
  • Feel brand new about it
Re: PINECIL: Inexpensive and outstanding soldering iron with digital control
« Reply #20 on: May 25, 2023, 10:05:30 AM »
^ Thanks. I ended up ordering a 100w plug. Looking forward to completing a project put off for far too long.
Logged
mg m20.21.23 ■ akg ck61.62.63 »  nbob■naiant
aercomp2 ■ v2∞3 ■ sx-m2d2
pcm-d100 ■ pmd661 ■ r44ocm ■ f3
Pages: 1 [2]  All   Go Up
« previous next »
 

RSS | Mobile
Page created in 0.042 seconds with 29 queries.
© 2002-2024 Taperssection.com
Powered by SMF