Taperssection.com

Gear / Technical Help => Ask The Tapers => Topic started by: 1st set only on October 29, 2004, 08:29:46 AM

Title: JB3 charger and puppy dont mix! Need help quick!!
Post by: 1st set only on October 29, 2004, 08:29:46 AM
hey all so our new puppy just chewed through my jb3 charger cable. I need help because a few shows are comming up that i want to tape and im running low on juice. i found a link on creatives site that had the chargers anyone here know of a brick and mortar place that i can get one quick? does Radio shack sell a facimaly?


help

dogs ok bye the way no harm done
Title: Re: JB3 charger and puppy dont mix! Need help quick!!
Post by: Humbug on October 29, 2004, 08:38:51 AM
I've got a spare UK charger if you get really stuck. I guess all you'll veed to do is change the plug as it is dual voltage and 50/60Hz.

It'll take a couple of weeks to reach you..

Why dont you resolder the cable (or get it done by someone?)
Title: Re: JB3 charger and puppy dont mix! Need help quick!!
Post by: Joe w. on October 29, 2004, 08:42:36 AM
why don't you just hack the cable and get the plastic couplers from radio shack?
Title: Re: JB3 charger and puppy dont mix! Need help quick!!
Post by: 1st set only on October 29, 2004, 08:50:03 AM
ill try the hack tonight but its pretty close to the "box" not much wiggle room
Title: Re: JB3 charger and puppy dont mix! Need help quick!!
Post by: John R on October 29, 2004, 08:55:45 AM
you could always open the box and solder on new leads
Title: Re: JB3 charger and puppy dont mix! Need help quick!!
Post by: The Kilted Taper on October 29, 2004, 09:34:39 AM
I've got 3 of the chargers if you need one. Let me know!
Title: Re: JB3 charger and puppy dont mix! Need help quick!!
Post by: Brian Skalinder on October 29, 2004, 10:57:31 AM
If you're in a pinch and you have some rechargable cells lying around, you could easily wire up a 4 x 1.2v rechargable cell external pack.  Cost would be ~$1.43.
Title: Re: JB3 charger and puppy dont mix! Need help quick!!
Post by: 1st set only on October 29, 2004, 12:52:07 PM
thanks for the move bri

what is the adaptaplug that i need for the jb3 if i go external pack or thould i just use what is left.

if all else fails ill take you up on your offer born again
Title: Re: JB3 charger and puppy dont mix! Need help quick!!
Post by: Brian Skalinder on October 31, 2004, 01:55:10 PM
what is the adaptaplug that i need for the jb3 if i go external pack or thould i just use what is left.

I used the stock plug / cord.  Dunno which adaptaplug, but it's in the JB3 FAQ in the Archival Info forum.
Title: Re: JB3 charger and puppy dont mix! Need help quick!!
Post by: mmmatt on November 01, 2004, 11:56:20 PM
Go buy a wally world car charger and charge it in the car.  You can do that quick untill you get your wall charger worked out.  Then you can hack the charger and use it to run external RC batts!!!!
Matt
Title: Re: JB3 charger and puppy dont mix! Need help quick!!
Post by: Nick Graham on November 02, 2004, 03:11:11 AM
Go buy a wally world car charger and charge it in the car.  You can do that quick untill you get your wall charger worked out.  Then you can hack the charger and use it to run external RC batts!!!!
Matt

I've been looking for a Wal-Mart car charger. What is it exactly I'd need?

Also, anyone know of a car charger that would work with a Eco-Charge and/or Oade 6v?
Title: Re: JB3 charger and puppy dont mix! Need help quick!!
Post by: mmmatt on November 05, 2004, 12:38:02 AM
It is in the electronics area by the personal cd players and such.  I think there are 2 models, and I think it was agreed that the larger one was best because of the potential for greater current draw at start-up.

Matt