Taperssection.com
Gear / Technical Help => Remote Power => Topic started by: Jason R on July 30, 2004, 03:06:10 PM
-
Can I power a DAp1 with a 12 volt.
-
if you regulate it down to 6
-
I believe it really wants 7.5V, but will operate on 6-8. Not 12, though.
-
I believe it really wants 7.5V, but will operate on 6-8. Not 12, though.
the DAP1 will run on a 6v?
-
I believe it really wants 7.5V, but will operate on 6-8. Not 12, though.
da-p1 will run safely at 13.5v. i run mine on 12v. even the output of the da-p1's ac adaptor is 13.5v, although it states 7.2v on the box.
marc
-
I believe it really wants 7.5V, but will operate on 6-8. Not 12, though.
da-p1 will run safely at 13.5v. i run mine on 12v. even the output of the da-p1's ac adaptor is 13.5v, although it states 7.2v on the box.
marc
?????
I have measured the UNLOADED voltage out from the DA-P1 AC adaptor to be 13.8 Volts DC. But it drops to a stable & well regulated 7.5 Volts (measured at the DA-P1 input terminal) when delivering the 650 to 800 or so mA the DA-P1 uses.
There are two power supply capacitors within the DA-P1 that see the DC input voltage. They are both rated for 10 Volts operation.
I take your statement above to mean that the DC-DC converter tackles a fully charged lead acid (13.6-14.5 Volts I imagine depending on your charger?).
Heat should not be a problem for the DC-DC converter. But linear regulators develop heat in proportion to the voltage across and heat shortens the expected lifetime of semiconductors.
I.e., I would not exceed 10 Volts when powering the DA-P1 with an external DC source.
Jon
-
I believe it really wants 7.5V, but will operate on 6-8. Not 12, though.
the DAP1 will run on a 6v?
that's all that anyone I know has ever used with it...
-
I believe it really wants 7.5V, but will operate on 6-8. Not 12, though.
da-p1 will run safely at 13.5v. i run mine on 12v. even the output of the da-p1's ac adaptor is 13.5v, although it states 7.2v on the box.
marc
?????
I have measured the UNLOADED voltage out from the DA-P1 AC adaptor to be 13.8 Volts DC. But it drops to a stable & well regulated 7.5 Volts (measured at the DA-P1 input terminal) when delivering the 650 to 800 or so mA the DA-P1 uses.
There are two power supply capacitors within the DA-P1 that see the DC input voltage. They are both rated for 10 Volts operation.
I take your statement above to mean that the DC-DC converter tackles a fully charged lead acid (13.6-14.5 Volts I imagine depending on your charger?).
Heat should not be a problem for the DC-DC converter. But linear regulators develop heat in proportion to the voltage across and heat shortens the expected lifetime of semiconductors.
I.e., I would not exceed 10 Volts when powering the DA-P1 with an external DC source.
Jon
jon, thanks for the detailed specs. i've ran the da-p1 with a 12v sla without any issues, but i will drop the voltage down further.
marc
-
I believe it really wants 7.5V, but will operate on 6-8. Not 12, though.
the DAP1 will run on a 6v?
that's all that anyone I know has ever used with it...
sweet!
I thought I was going to end up carrying 2 types of lead :)
-
:)
-
6v 7.2amp runs it for AWHILE too, i used to get 10hrs+ from one 6v7.2a