Become a Site Supporter and Never see Ads again!

Author Topic: How well do 1/8" couplers pass along power provided by a preamp?  (Read 4359 times)

0 Members and 1 Guest are viewing this topic.

Offline ycoop

  • Trade Count: (9)
  • Taperssection Member
  • ***
  • Posts: 647
  • Gender: Male
Recently acquired a CA9100, and want to be able to leave it running in my bag at the base of a 9 ft stand. The CA-14s I have are wired with only 5 feet of cable, so I'd like to extend them with coupler and additional length of cabling. Will a quality coupler be able to pass along the 9V from the CA9100? If so, what recs do you have for a brand that produces quality couplers?
Mics: Avantone CK-1s, AT853 c+o
Pres: CA9100
Recorders: DR-60d mkII, DR-2d

Online Gutbucket

  • record > listen > revise technique
  • Trade Count: (15)
  • Needs to get out more...
  • *****
  • Posts: 15698
  • Gender: Male
  • "Better to love music than respect it" ~Stravinsky
Re: How well do 1/8" couplers pass along power provided by a preamp?
« Reply #1 on: October 10, 2018, 02:07:13 PM »
Works.  A 6' to 10' Ratshack stereo-mini headphone extension cable will do the job.  I'd not extend the run any further than that.  The biggest issue is preventing intermittency or outright disconnection at the non-locking mini-jack connections.  Clean all plugs and jacks well before connecting and secure the connections well with a wrap of gaff tape.  Good to velcro-tie your cables to the stand both above and below the connection to prevent any mechanical stress on the connection.

For a better solution, reterminate to locking connectors (such as mini-XLR) or make a permanent splice within a short section of tubing well secured with glue-backed heat-shrink over the assembly extending out a couple inches to each side to boht secure the cables and serve as strain-relief.
musical volition > vibrations > voltages > numeric values > voltages > vibrations> virtual teleportation time-machine experience
Better recording made easy - >>Improved PAS table<< | Made excellent- >>click here to download the Oddball Microphone Technique illustrated PDF booklet<< (note: This is a 1st draft, now several years old and in need of revision!  Stay tuned)

Offline ycoop

  • Trade Count: (9)
  • Taperssection Member
  • ***
  • Posts: 647
  • Gender: Male
Re: How well do 1/8" couplers pass along power provided by a preamp?
« Reply #2 on: October 10, 2018, 05:32:21 PM »
Works.  A 6' to 10' Ratshack stereo-mini headphone extension cable will do the job.  I'd not extend the run any further than that.  The biggest issue is preventing intermittency or outright disconnection at the non-locking mini-jack connections.  Clean all plugs and jacks well before connecting and secure the connections well with a wrap of gaff tape.  Good to velcro-tie your cables to the stand both above and below the connection to prevent any mechanical stress on the connection.

For a better solution, reterminate to locking connectors (such as mini-XLR) or make a permanent splice within a short section of tubing well secured with glue-backed heat-shrink over the assembly extending out a couple inches to each side to boht secure the cables and serve as strain-relief.

Thanks for the thorough answer, as usual.  :cheers:

A few questions:

How hard of a soldering job is converting the TRS to mini-xlr?
What's the best way to clean the plugs and jacks?
Mics: Avantone CK-1s, AT853 c+o
Pres: CA9100
Recorders: DR-60d mkII, DR-2d

Online Gutbucket

  • record > listen > revise technique
  • Trade Count: (15)
  • Needs to get out more...
  • *****
  • Posts: 15698
  • Gender: Male
  • "Better to love music than respect it" ~Stravinsky
Re: How well do 1/8" couplers pass along power provided by a preamp?
« Reply #3 on: October 10, 2018, 06:15:34 PM »
90%+ alcohol, or any commercial contact cleaner like Caig, etc.

Depends on the wiring and your soldering skills.  Not difficult, but can be challenging if the wires are super tiny.  More attention to detail in getting good solder joints and securing the connector so as to be robust.
musical volition > vibrations > voltages > numeric values > voltages > vibrations> virtual teleportation time-machine experience
Better recording made easy - >>Improved PAS table<< | Made excellent- >>click here to download the Oddball Microphone Technique illustrated PDF booklet<< (note: This is a 1st draft, now several years old and in need of revision!  Stay tuned)

ThePiedPiper

  • Guest
  • Trade Count: (0)
Re: How well do 1/8" couplers pass along power provided by a preamp?
« Reply #4 on: November 15, 2018, 11:45:10 PM »
What a GREAT question and (as usual) a great reply from sensei Gutbucket.  :clapping:

 

RSS | Mobile
Page created in 0.143 seconds with 34 queries.
© 2002-2024 Taperssection.com
Powered by SMF