Become a Site Supporter and Never see Ads again!

Author Topic: HPF options on the Lunatec V3?  (Read 2801 times)

0 Members and 1 Guest are viewing this topic.

Offline One Cylinder

  • Site Supporter
  • Trade Count: (5)
  • Taperssection Regular
  • *
  • Posts: 218
  • Gender: Male
HPF options on the Lunatec V3?
« on: December 15, 2011, 04:37:20 PM »
I can't tell from the V3's owner manual -- which set of specs apply to a stock V3?

HPF SWITCH POSITION and CUTOFF FREQUENCY:

1 = 100Hz
2 = 50Hz
 
OR

1 = 125Hz
2 = 75Hz

Thanks...

Schoeps MK4(x2) MK21(x2)
Schoeps CMC6(x4) CMC1K(x2)
Sonosax SX-M2, Grace Design ACM Lunatec V3
Roland OCM R-44

Offline page

  • Trade Count: (25)
  • Needs to get out more...
  • *****
  • Posts: 8388
  • Gender: Male
  • #TeamRetired
Re: HPF options on the Lunatec V3?
« Reply #1 on: December 15, 2011, 04:39:49 PM »
they both do, it's controlled via switchable jumpers inside the unit
"This is a common practice we have on the bus; debating facts that we could easily find through printed material. It's like, how far is it today? I think it's four hours, and someone else comes in at 11 hours, and well, then we'll... just... talk about it..." - Jeb Puryear

"Nostalgia ain't what it used to be." - Jim Williams

Offline One Cylinder

  • Site Supporter
  • Trade Count: (5)
  • Taperssection Regular
  • *
  • Posts: 218
  • Gender: Male
Re: HPF options on the Lunatec V3?
« Reply #2 on: December 16, 2011, 02:32:03 AM »
......should have been more clear -  when the V3 leaves the production floor, to which specs are the jumpers set?

Schoeps MK4(x2) MK21(x2)
Schoeps CMC6(x4) CMC1K(x2)
Sonosax SX-M2, Grace Design ACM Lunatec V3
Roland OCM R-44

Offline Brian Skalinder

  • Complaint Dept.
  • Trade Count: (28)
  • Needs to get out more...
  • *****
  • Posts: 18868
  • Gender: Male
Re: HPF options on the Lunatec V3?
« Reply #3 on: December 16, 2011, 02:50:31 AM »
Only way to know for certain how your unit was configured on the production floor:  open it up and check the jumpers.  It's very easy to do, and as long as you don't mess around with anything inside, you can't hurt it.
Milab VM-44 Links > Fostex FR-2LE or
Naiant IPA (tinybox format) >
Roland R-05

Offline F.O.Bean

  • Team Schoeps Tapir that
  • Trade Count: (126)
  • Needs to get out more...
  • *****
  • Posts: 40690
  • Gender: Male
  • Taperus Maximus
    • MediaFire Recordings
Re: HPF options on the Lunatec V3?
« Reply #4 on: December 17, 2011, 12:51:00 AM »
When new, theyre at 50/100
Schoeps MK 4V & MK 41V ->
Schoeps 250|0 KCY's (x2) ->
Naiant +60v|Low Noise PFA's (x2) ->
DarkTrain Right Angle Stubby XLR's (x3) ->
Sound Devices MixPre-6 & MixPre-3

http://www.archive.org/bookmarks/diskobean
http://www.archive.org/bookmarks/Bean420
http://bt.etree.org/mytorrents.php
http://www.mediafire.com/folder/j9eu80jpuaubz/Recordings

Offline One Cylinder

  • Site Supporter
  • Trade Count: (5)
  • Taperssection Regular
  • *
  • Posts: 218
  • Gender: Male
Re: HPF options on the Lunatec V3?
« Reply #5 on: December 23, 2011, 01:12:54 PM »
.....Thanks Bean.  That was a tough one!   ;D

Schoeps MK4(x2) MK21(x2)
Schoeps CMC6(x4) CMC1K(x2)
Sonosax SX-M2, Grace Design ACM Lunatec V3
Roland OCM R-44

 

RSS | Mobile
Page created in 0.077 seconds with 34 queries.
© 2002-2024 Taperssection.com
Powered by SMF