Become a Site Supporter and Never see Ads again!

Author Topic: Gepco mic cable question  (Read 7338 times)

0 Members and 1 Guest are viewing this topic.

Offline aysvideo

  • Trade Count: (15)
  • Taperssection Regular
  • **
  • Posts: 141
Gepco mic cable question
« on: February 13, 2017, 03:57:16 PM »
Has anybody ever used this to make XLR cables?   http://www.markertek.com/product/72401ez-bk/gepco-72401ez-2-cond-24-ga-twisted-pair-audio-cable-black-per-foot

I was thinking about trying it because I have some spare Neutrik connectors lying around collecting dust.  If I do get some, would the red go to pin 2, and the black to 3, or the other way around?  Or would it not matter as long as I'm consistent from one cable to the next?  Also, I suppose the drain wire on this cable would go to pin 1 as the ground, but would I tie that first to the foil shielding before soldering it or not use the shielding at all?  Most cable I've used in the past has a blue, a white and no separate drain wire, so I use the blue for pin 2, the white for 3, and the shield is what I've always used as the ground.

Offline ScoobieKW

  • Trade Count: (3)
  • Taperssection All-Star
  • ****
  • Posts: 1664
    • ScoobieSnax Audio Archive
Re: Gepco mic cable question
« Reply #1 on: February 13, 2017, 05:57:28 PM »
When in doubt, check the Rane cheat sheet. Red or White for 2 and Black for 3 is a common convention. Electrically the same Red on 3 but following convention helps in repairs and troubleshooting.

http://www.rane.com/note110.html

The drain wire is convenient, use a continuity tester to see if it is tied to the shield. If not continue using shield as you have in the past.
Busman BSC1, AT853 (O,C),KAM i2 Chuck Mod (C), Nak 300 (C),
M10, UA-5, US-1800, Presonus Firepod

http://kennedy-williams.net/scoobiesnax/

Offline aysvideo

  • Trade Count: (15)
  • Taperssection Regular
  • **
  • Posts: 141
Re: Gepco mic cable question
« Reply #2 on: February 13, 2017, 07:13:23 PM »
When in doubt, check the Rane cheat sheet. Red or White for 2 and Black for 3 is a common convention. Electrically the same Red on 3 but following convention helps in repairs and troubleshooting.

http://www.rane.com/note110.html

The drain wire is convenient, use a continuity tester to see if it is tied to the shield. If not continue using shield as you have in the past.

Thanks much.  Just to make sure I understand, are you suggesting that if the shield and drain are not tied together, to use the shield for pin one and ignore the drain wire?

Offline Hypnocracy

  • Site Supporter
  • Trade Count: (46)
  • Needs to get out more...
  • *
  • Posts: 2011
  • Hypnocratic Missionary
    • Hypno on teh LMA
Re: Gepco mic cable question
« Reply #3 on: February 13, 2017, 07:35:24 PM »
From the description on  Markertek page...
Quote
Foil shield with same gage drain wire facilitates quick shield termination. Twenty-four gage conductors are easier to terminate while still maintaining low DCR. Ideal for patchbay wiring or mobile production trucks.

The Foil Shield I've seen in the past were polyester film with aluminum surface and included the drain wire...how is that handled?
_____________
hypno on teh Archive

This must be heaven -- 'cause here's where the rainbow ends
If this ain't the real thing, then it's close enough to pretend

Offline ScoobieKW

  • Trade Count: (3)
  • Taperssection All-Star
  • ****
  • Posts: 1664
    • ScoobieSnax Audio Archive
Re: Gepco mic cable question
« Reply #4 on: February 13, 2017, 07:51:45 PM »
Take a simple voltmeter and test for continuity between the drain and shield. If they are tied then go ahead and use the drain.
Busman BSC1, AT853 (O,C),KAM i2 Chuck Mod (C), Nak 300 (C),
M10, UA-5, US-1800, Presonus Firepod

http://kennedy-williams.net/scoobiesnax/

 

RSS | Mobile
Page created in 0.052 seconds with 34 queries.
© 2002-2024 Taperssection.com
Powered by SMF