Become a Site Supporter and Never see Ads again!

Author Topic: Help with I.D. and source for this mic holder  (Read 277 times)

0 Members and 1 Guest are viewing this topic.

Offline Melanie

  • Trade Count: (3)
  • Taperssection Member
  • ***
  • Posts: 750
Help with I.D. and source for this mic holder
« on: October 23, 2022, 05:17:58 PM »
Lost one of these mic holders for Shoeps v4, when I took it out of the bag at a Wolf Bros. show Friday it flew off the bar and wound up over the balcony rail. Fortunately the floor was empty so no one was hit by it but could not find it. Need help with I.D. and source if available. Thanks, Bob
Melanie and Bob

Offline audBall

  • Trade Count: (37)
  • Needs to get out more...
  • Posts: 6384
  • Gender: Male
  • Feel brand new about it
Re: Help with I.D. and source for this mic holder
« Reply #1 on: October 23, 2022, 05:22:59 PM »
I recommend these with the far more durable metal base.

https://taperssection.com/index.php?topic=163086.0
mg m20.21 ■ akg ck61.62.63 » nbob|naiant » aercomp2 ■ v2
dpa 4061 » mma-a.6000 ■ spsb-10(9v)
m10 ■ d100 ■ r44ocm

Offline Melanie

  • Trade Count: (3)
  • Taperssection Member
  • ***
  • Posts: 750
Re: Help with I.D. and source for this mic holder
« Reply #2 on: October 23, 2022, 05:31:28 PM »
But will it fit on the existing bar? I'd like to keep the same setup. Does anyone recognize this set up? Melanie got it 20 years or more ago, can't remember name or source.
« Last Edit: October 23, 2022, 05:34:11 PM by Melanie »
Melanie and Bob

Offline audBall

  • Trade Count: (37)
  • Needs to get out more...
  • Posts: 6384
  • Gender: Male
  • Feel brand new about it
Re: Help with I.D. and source for this mic holder
« Reply #3 on: October 23, 2022, 05:42:44 PM »
Yeah, it should. That lower mount appears to be an older version of the Sabra SOM-ST2 bar, or similar.

https://www.amazon.com/Sabra-Som-ST2-Stereo-Bar/dp/B00080H3FC
mg m20.21 ■ akg ck61.62.63 » nbob|naiant » aercomp2 ■ v2
dpa 4061 » mma-a.6000 ■ spsb-10(9v)
m10 ■ d100 ■ r44ocm

Offline Melanie

  • Trade Count: (3)
  • Taperssection Member
  • ***
  • Posts: 750
Re: Help with I.D. and source for this mic holder
« Reply #4 on: October 24, 2022, 10:47:40 AM »
Thanks for the help, we'll pick one up and see what differences there are in materials.
Melanie and Bob

Online goodcooker

  • Trade Count: (41)
  • Needs to get out more...
  • *****
  • Posts: 3904
  • Gender: Male
  • goes to 11
Re: Help with I.D. and source for this mic holder
« Reply #5 on: October 24, 2022, 11:09:04 AM »
If the entire thing went over the rail you need two pieces to replace it. The mount is a Schoeps SGM miniature mic clip. The other piece that slides onto the bar may be tougher to replace. It looks like a Sabra Som stereo mount but an older version.

Is the bar 4 sided or hexagonal? The newer version of this stereo bar linked above is hexagonal so a replacement mount for the newer bar may not work if the bar is four sided.
Line Audio CM3 || ADK A51 type IV
SD MixpreD || Oade Warm Mod UA5
Tascam DR680 || Marantz PMD661 || Korg MR1 (homebrew internal battery mod)

http://www.archive.org/bookmarks/goodcooker

"Are you the Zman?" - fan at Panic 10-08-10 Kansas City
"I don't know who left this perfectly good inflatable wook doll here, but if I'm blowing her up, I'm keeping her." -  hoppedup

Offline Melanie

  • Trade Count: (3)
  • Taperssection Member
  • ***
  • Posts: 750
Re: Help with I.D. and source for this mic holder
« Reply #6 on: October 24, 2022, 11:56:12 AM »
If the entire thing went over the rail you need two pieces to replace it. The mount is a Schoeps SGM miniature mic clip. The other piece that slides onto the bar may be tougher to replace. It looks like a Sabra Som stereo mount but an older version.

Is the bar 4 sided or hexagonal? The newer version of this stereo bar linked above is hexagonal so a replacement mount for the newer bar may not work if the bar is four sided.
bar is six sided as is the original, just lost one of the mic mounts, not the whole bar set up. I am ordering it but I think that the  quality won't be as good as the original. If anyone has one of the mic mounts (not the clip for mic, but the end piece) let me know. Hopefully the sucker will just slide right on to the orig.
Melanie and Bob

 

RSS | Mobile
Page created in 0.046 seconds with 29 queries.
© 2002-2022 Taperssection.com
Powered by SMF