Become a Site Supporter and Never see Ads again!

Author Topic: Specific 4.7k Mod question  (Read 2390 times)

0 Members and 1 Guest are viewing this topic.

Offline Cheesecadet

  • Trade Count: (21)
  • Needs to get out more...
  • *****
  • Posts: 3016
  • Gender: Male
  • http://db.etree.org/cheesecadet
Specific 4.7k Mod question
« on: November 10, 2019, 11:30:16 AM »
Does anyone know if it is possible to make a dual mini-xlr cable to a stereo 1/8" with the 4.7k mod in that interconnect?

I ask because I have a pair of AT933s w/ AT853 SC caps that currently terminate in mini-XLR and have a specific interconnect of dual mini-XLR to 6-Pin that I use with my Tinybox.

I am hoping the above cable is another option I might be able to use so I could run the AT mics into my PIPsqueak using an 1/8" connector with the 4.7k mod in it to avoid distortion.

All this in a effort to keep making my lopro gear smaller with the versatility of using two different preamps and all the while keeping the mini-XLR connectors on the mics.  Hopefully that makes sense!?!?

Any info is greatly appreciated!

Ryan
AKG 481's, DPA 4061's (Matched), AT ES933's w/ AT853-ELE's (SC/C/O), ECM-19B's, MixPre-3, A10, M10 x 2, Hi Ho Silvers, Various Darktrain & GAKables

Vinyl:
Fluance RT83 Reference > MCS 3230 Receiver > Realistic MC-500's (NOS)

Upcoming:
02/10 J. Dilla
02/14 Wiliie Waldman & The Chocolate Factory
02/15 Gabe & Giz
02/16 GM5
02/28 Grace Potter

Offline kuba e

  • Trade Count: (1)
  • Taperssection Member
  • ***
  • Posts: 492
  • Gender: Male
Re: Specific 4.7k Mod question
« Reply #1 on: November 10, 2019, 03:58:44 PM »
Does anyone know if it is possible to make a dual mini-xlr cable to a stereo 1/8" with the 4.7k mod in that interconnect?

Yes Rayan, you can do it. I didn't do it myself but it shouldn't be difficult. Here is a thread about it.
http://taperssection.com/index.php?topic=142731.0

All this in a effort to keep making my lopro gear smaller with the versatility of using two different preamps and all the while keeping the mini-XLR connectors on the mics.  Hopefully that makes sense!?!?

Sure, it make sense! Just be sure your PIPsqueak is giving right voltage for AT mics.
« Last Edit: November 10, 2019, 04:01:39 PM by kuba e »

Offline Humbug

  • Trade Count: (5)
  • Needs to get out more...
  • *****
  • Posts: 2161
  • Gender: Male
  • Humbug Hum Rejection Unit
    • Trading site
Re: Specific 4.7k Mod question
« Reply #2 on: November 11, 2019, 07:02:55 AM »
Darn - my PIPsqueaks both have the 4-pin binder....good luck with your mod.
UK based taper: MK4>Nbox Platinum>PCM-M10
AT853C>CA9200 / PIPsqueak>Tascam DR-2D

http://www.archive.org/bookmarks/Humbug66

Offline Humbug

  • Trade Count: (5)
  • Needs to get out more...
  • *****
  • Posts: 2161
  • Gender: Male
  • Humbug Hum Rejection Unit
    • Trading site
Re: Specific 4.7k Mod question
« Reply #3 on: November 11, 2019, 07:05:14 AM »
Another photo which makes it clear how I use them...should get you along the right lines.
UK based taper: MK4>Nbox Platinum>PCM-M10
AT853C>CA9200 / PIPsqueak>Tascam DR-2D

http://www.archive.org/bookmarks/Humbug66

 

RSS | Mobile
Page created in 0.111 seconds with 32 queries.
© 2002-2024 Taperssection.com
Powered by SMF