Become a Site Supporter and Never see Ads again!

Author Topic: Sound Devices USBPre2 (Part Duex)  (Read 64579 times)

0 Members and 2 Guests are viewing this topic.

Offline page

  • Trade Count: (25)
  • Needs to get out more...
  • *****
  • Posts: 8388
  • Gender: Male
  • #TeamRetired
Sound Devices USBPre2 (Part Duex)
« on: December 14, 2011, 10:12:19 AM »
Part 1: http://taperssection.com/index.php?topic=139081



I haven't dug deep in the thread yet....   but does anyone successfully power the USBPre 2 off of the Tekkeon USB output?  Thanks.

Yep. Acidjack has been doing this for as long as he's owned both units.

I have as well. (722 off of the main out and the usbpre2 off of the usb slot)

Cool thanks fellas!  I'm thinkin about jumpin on board.
So....   this has the same (or very similar) pre amp and ADC as the 744 correct?  I'm lookin to use it for the ADC mainly.

same preamp as the 788 specifically and the same ADC as used in all of the 7 series.

The difference is specs on the line-in is it can handle up to +28dbu before clipping on the line-in (balanced TRS jacks) compared to the +26dbu for the 7x2 and 744 (I havn't looked at the 788s to see if they are the same). If you do use it with the preamp, look at whether or not you will need the -15db pads or not. For quiet mics, you may not and instead just use very little gain. food for though.
"This is a common practice we have on the bus; debating facts that we could easily find through printed material. It's like, how far is it today? I think it's four hours, and someone else comes in at 11 hours, and well, then we'll... just... talk about it..." - Jeb Puryear

"Nostalgia ain't what it used to be." - Jim Williams

Offline page

  • Trade Count: (25)
  • Needs to get out more...
  • *****
  • Posts: 8388
  • Gender: Male
  • #TeamRetired
Re: Sound Devices USBPre2 (Part Duex)
« Reply #1 on: December 14, 2011, 10:13:50 AM »
bump so it shows up first in the forum section until SClassical locks the other thread.
"This is a common practice we have on the bus; debating facts that we could easily find through printed material. It's like, how far is it today? I think it's four hours, and someone else comes in at 11 hours, and well, then we'll... just... talk about it..." - Jeb Puryear

"Nostalgia ain't what it used to be." - Jim Williams

kirk97132

  • Guest
  • Trade Count: (0)
Re: Sound Devices USBPre2 (Part Duex)
« Reply #2 on: December 14, 2011, 11:13:12 AM »
marking therad 8)

Offline acidjack

  • Site Supporter
  • Trade Count: (37)
  • Needs to get out more...
  • *
  • Posts: 5845
  • Gender: Male
Re: Sound Devices USBPre2 (Part Duex)
« Reply #3 on: December 14, 2011, 01:39:14 PM »
The USBPre2 is one of my favorite pieces of gear.  Versatile, lightweight, elegant design, can co-power with deck through a Tekkeon, and can use as an external A/D and/or headphone amp with the computer.

Oh, and has same pres as a $6000 recorder.  What's not to like?
Mics: Schoeps MK4V, MK41V, MK5, MK22> CMC6, KCY 250/5, KC5, NBob; MBHO MBP603/KA200N, AT 3031, DPA 4061 w/ d:vice, Naiant X-X, AT 853c, shotgun, Nak300
Pres/Power: Aerco MP2, tinybox v2  [KCY], CA-UBB
Decks: Sound Devices MixPre 6, Zoom F8, M10, D50

My recordings on nyctaper.com: http://www.nyctaper.com/?tag=acidjack | LMA: http://www.archive.org/bookmarks/acidjack | twitter: http://www.twitter.com/acidjacknyc | Soundcloud: https://soundcloud.com/acidjacknyc

Offline yug du nord

  • ...til things never seen seem familiar…
  • Trade Count: (56)
  • Needs to get out more...
  • *****
  • Posts: 5537
  • made with natural flavor
Re: Sound Devices USBPre2 (Part Duex)
« Reply #4 on: December 14, 2011, 02:08:15 PM »
If by chance anyone is looking to sell, let me know.
.....got a blank space where my mind should be.....

Offline bhadella

  • Trade Count: (9)
  • Taperssection All-Star
  • ****
  • Posts: 1851
  • Gender: Male
  • Toiling away the day...
    • http://db.etree.org/bhadella1
Re: Sound Devices USBPre2 (Part Duex)
« Reply #5 on: December 14, 2011, 02:55:03 PM »
Although I prefer my Sonosax as a pre-amp, I think the a/d is top notch and has improved my recordings using it as an a/d.   I love that it can take a hot signal (via 1/4) and is very easy to power.   Add to that feature list that that you can clock it to another a/d makes it a great value. 
"Your ideas are intriguing to me and I wish to subscribe to your newsletter. "

Offline page

  • Trade Count: (25)
  • Needs to get out more...
  • *****
  • Posts: 8388
  • Gender: Male
  • #TeamRetired
Re: Sound Devices USBPre2 (Part Duex)
« Reply #6 on: December 14, 2011, 02:59:06 PM »
Although I prefer my Sonosax as a pre-amp, I think the a/d is top notch and has improved my recordings using it as an a/d.   I love that it can take a hot signal (via 1/4) and is very easy to power.   Add to that feature list that that you can clock it to another a/d makes it a great value.

this.

That was the big attraction for me, I can mate it with my 722 and run 4 channel or use it as a DAC/headamp when at home. I can even use it as the intermediary and convert to/from optical/rca spdif without loss (emailed SD and asked once since my MD player has optical out and my 722 didnt).
"This is a common practice we have on the bus; debating facts that we could easily find through printed material. It's like, how far is it today? I think it's four hours, and someone else comes in at 11 hours, and well, then we'll... just... talk about it..." - Jeb Puryear

"Nostalgia ain't what it used to be." - Jim Williams

Offline Beedy

  • Trade Count: (0)
  • Taperssection Newbie
  • *
  • Posts: 3
Re: Sound Devices USBPre2 (Part Duex)
« Reply #7 on: December 14, 2011, 08:22:52 PM »
this.

That was the big attraction for me, I can mate it with my 722 and run 4 channel or use it as a DAC/headamp when at home. I can even use it as the intermediary and convert to/from optical/rca spdif without loss (emailed SD and asked once since my MD player has optical out and my 722 didnt).
[/quote]


How did you connect your 722 with the usbpre2 to run 4 channel?

Offline hi and lo

  • Trade Count: (38)
  • Needs to get out more...
  • *****
  • Posts: 2294
Re: Sound Devices USBPre2 (Part Duex)
« Reply #8 on: December 14, 2011, 08:54:51 PM »
this.

That was the big attraction for me, I can mate it with my 722 and run 4 channel or use it as a DAC/headamp when at home. I can even use it as the intermediary and convert to/from optical/rca spdif without loss (emailed SD and asked once since my MD player has optical out and my 722 didnt).
[/i][/i]

How did you connect your 722 with the usbpre2 to run 4 channel?
[/quote]

You need another 2-channel recorder with a digital input (or output). By connecting the USBPre2's digital input to the 722 or any recorder with a digital output, the USBPre2 will sync it's clock with the external source. Then it's just a matter of connecting another deck, like a Sony D50, to the USBPre2's digital output.

It other words, the USBPre2's digital input ignores audio portion of a data stream, but syncs to the sample rate.

Offline page

  • Trade Count: (25)
  • Needs to get out more...
  • *****
  • Posts: 8388
  • Gender: Male
  • #TeamRetired
Re: Sound Devices USBPre2 (Part Duex)
« Reply #9 on: December 14, 2011, 10:49:55 PM »
You need another 2-channel recorder with a digital input (or output). By connecting the USBPre2's digital input to the 722 or any recorder with a digital output, the USBPre2 will sync it's clock with the external source. Then it's just a matter of connecting another deck, like a Sony D50, to the USBPre2's digital output.

It other words, the USBPre2's digital input ignores audio portion of a data stream, but syncs to the sample rate.

Correct. I have a D50 (which is one of the most economical digital in recorders) and I run a spdif cable from aes-id out on the 722 to spdif in on the usbpre2 and set the pre2 to line/mic. Just make sure to turn on the 722 fully before turning on the usbpre2, I've had odd things happen when it trys to sync up different clock sources than when it turned on. There is probably some rhyme and reason to it, but I didn't spend enough time trying to figure it out. SD advises a delayed turn on practice when clocking multiple 7 series units and I don't think it's unreasonable to apply the same standard here.

"This is a common practice we have on the bus; debating facts that we could easily find through printed material. It's like, how far is it today? I think it's four hours, and someone else comes in at 11 hours, and well, then we'll... just... talk about it..." - Jeb Puryear

"Nostalgia ain't what it used to be." - Jim Williams

Offline acidjack

  • Site Supporter
  • Trade Count: (37)
  • Needs to get out more...
  • *
  • Posts: 5845
  • Gender: Male
Re: Sound Devices USBPre2 (Part Duex)
« Reply #10 on: December 15, 2011, 11:56:17 AM »
You need another 2-channel recorder with a digital input (or output). By connecting the USBPre2's digital input to the 722 or any recorder with a digital output, the USBPre2 will sync it's clock with the external source. Then it's just a matter of connecting another deck, like a Sony D50, to the USBPre2's digital output.

It other words, the USBPre2's digital input ignores audio portion of a data stream, but syncs to the sample rate.

Correct. I have a D50 (which is one of the most economical digital in recorders) and I run a spdif cable from aes-id out on the 722 to spdif in on the usbpre2 and set the pre2 to line/mic. Just make sure to turn on the 722 fully before turning on the usbpre2, I've had odd things happen when it trys to sync up different clock sources than when it turned on. There is probably some rhyme and reason to it, but I didn't spend enough time trying to figure it out. SD advises a delayed turn on practice when clocking multiple 7 series units and I don't think it's unreasonable to apply the same standard here.

To add to this, the "page method" has worked for Fried Chicken Boy and I going R44 #1>USBPre>R-44 #2 to make an 8-channel mix.  Thanks to page I no longer have to even contemplate running a 680 ever again. (sorry for the gratuitous 680 insult in advance)  :P
Mics: Schoeps MK4V, MK41V, MK5, MK22> CMC6, KCY 250/5, KC5, NBob; MBHO MBP603/KA200N, AT 3031, DPA 4061 w/ d:vice, Naiant X-X, AT 853c, shotgun, Nak300
Pres/Power: Aerco MP2, tinybox v2  [KCY], CA-UBB
Decks: Sound Devices MixPre 6, Zoom F8, M10, D50

My recordings on nyctaper.com: http://www.nyctaper.com/?tag=acidjack | LMA: http://www.archive.org/bookmarks/acidjack | twitter: http://www.twitter.com/acidjacknyc | Soundcloud: https://soundcloud.com/acidjacknyc

Offline DigiGal

  • AES Associate Member
  • Trade Count: (30)
  • Needs to get out more...
  • *****
  • Posts: 2583
  • Gender: Female
  • Stay healthy and safe!
    • DigiGal Internet Archive Recordings
Re: Sound Devices USBPre2 (Part Duex)
« Reply #11 on: December 27, 2011, 10:27:10 PM »
Curious, anyone using the limiter in this box?  Haven't seen any comments about it reading through the posts.
Mics: AKG CK91/CK94/CK98/SE300 D-330BT | DPA 4060 4061 4266 | Neumann TLM 103 | Senn ME66/K6/K6RD MKE2 MD421 MD431 | Shure VP88 SM7B SM63L SM58 Anniversary Cables: Gotham GAC-4/1 Quad w/Neutrik EMC | Gotham GAC-2pair w/AKG MK90/3 connectors | DigiGal AES>S/PDIF cable Preamp: SD MixPre-D Recorders: SD MixPre 6 | Marantz PMD 661 Edit: 2011 27" 3.4GHz Quad i7 iMac High Sierra | 2020 13" MBA Quad i7 Catalina | Wave Editor | xACT | Transmission | FCP X 

Offline F.O.Bean

  • Team Schoeps Tapir that
  • Trade Count: (126)
  • Needs to get out more...
  • *****
  • Posts: 40699
  • Gender: Male
  • Taperus Maximus
    • MediaFire Recordings
Re: Sound Devices USBPre2 (Part Duex)
« Reply #12 on: December 28, 2011, 04:27:37 AM »
Curious, anyone using the limiter in this box?  Haven't seen any comments about it reading through the posts.

I think as a general rule of thumb, using Limiters/AGC/etc is frowned upon! So I doubt you will have too many people chiming in to this thread about the USBPre2's Limiters ;)

Never know tho, maybe a few people ARE using them ??? :)
Schoeps MK 4V & MK 41V ->
Schoeps 250|0 KCY's (x2) ->
Naiant +60v & +48v/40v Low Noise PFA's (x2) ->
DarkTrain Right Angle Stubby XLR's (x3) ->
Sound Devices MixPre-6 & MixPre-3

http://www.archive.org/bookmarks/diskobean
http://bt.etree.org/mytorrents.php
http://www.mediafire.com/folder/j9eu80jpuaubz/Recordings

kirk97132

  • Guest
  • Trade Count: (0)
Re: Sound Devices USBPre2 (Part Duex)
« Reply #13 on: December 28, 2011, 12:46:54 PM »
Not the limiter but have been using the 15dB pad.  Found that it was all I needed even when using mics on stage.

Offline page

  • Trade Count: (25)
  • Needs to get out more...
  • *****
  • Posts: 8388
  • Gender: Male
  • #TeamRetired
Re: Sound Devices USBPre2 (Part Duex)
« Reply #14 on: December 28, 2011, 04:07:02 PM »
Not the limiter but have been using the 15dB pad.  Found that it was all I needed even when using mics on stage.

I've use the pad, all the time, have to. I ran my ck950s couple weeks ago with the gain turned all the way down, 15db pad in, and peaked around -5.  :o
"This is a common practice we have on the bus; debating facts that we could easily find through printed material. It's like, how far is it today? I think it's four hours, and someone else comes in at 11 hours, and well, then we'll... just... talk about it..." - Jeb Puryear

"Nostalgia ain't what it used to be." - Jim Williams

 

RSS | Mobile
Page created in 0.048 seconds with 38 queries.
© 2002-2024 Taperssection.com
Powered by SMF