Become a Site Supporter and Never see Ads again!

Author Topic: First build in a while  (Read 6313 times)

0 Members and 1 Guest are viewing this topic.

Offline checht

  • Site Supporter
  • Trade Count: (7)
  • Taperssection Member
  • *
  • Posts: 817
  • Let's meet at alternate foods at the break
First build in a while
« on: April 03, 2023, 12:30:55 AM »
Thought I’d get back to building cables, it's been a few decades. Following Voltronic’s advice I ordered Redco 4 channel snake cable and a Pinecil. Got Neutrik xlrs and colored boots to compensate for poor vision. Got a LED light magnifier soldering station to supplement my trusty vise.

Build went fine, if slower than when I had good vision. Over the course of wiring 8 connectors, memorized but forgotten motor skills and techniques came back to me. Using full size connectors was nice, reducing the need to keep leads short like would be needed for stubbies. The snake will be used when sanctioned to record, and weighs 6#, so size of connectors wasn’t super critical. I tested the cables, all was fine, continuity and no shorts. Then I shrank the shrink tubing and made an unforced error. Lingered too long on one cable, which fused the wires inside and shorted them. Lesson learned.

Picture below, it's 4 channels x 100'. Solders look decent to me.

The third picture is one of the last sets of cables I made back in the day, built in the dorms in 1983, for stealthing with my km84i pair. It was Vermont/NorthEast, so I’d wear a Russian winter hat with the ear coverings snapped up and put the mics in the flaps. Used ‘em for B52s @ the Fillmore when they warmed up for their Love Shack tour:

https://www.dropbox.com/scl/fo/qoyvp69vfytroyv3tv6up/h?dl=0&rlkey=lvh4c8y8rvmeho57vb85nccex

Still using the shorties, mostly for SBD feeds when I’m running at the board. Hope the new snake is similarly durable.

Thanks all, for the input along the way, it helped a lot.
MK41s, MK22s; Vanguard V1s matched pair
Schoeps kcy5, nbob actives
Naiant PFA 60v, PFA 48v, IPA
Sound Devices MP-6II; Sony PCM-A10

Recordings at LMA

Offline morst

  • I think I found an error on the internet; #UnionStrong
  • Trade Count: (2)
  • Needs to get out more...
  • *****
  • Posts: 6136
Re: First build in a while
« Reply #1 on: April 03, 2023, 01:33:22 AM »

I've probably mentioned this in other threads but a double "Third hand" weighted base, with a couple alligator clips can really make things easy in terms of holding wires in place to allow you to use one hand on the soldering iron and the other on the solder itself.



https://toad.social/@morst spoutible.com/morst post.news/@acffhmorst

Offline checht

  • Site Supporter
  • Trade Count: (7)
  • Taperssection Member
  • *
  • Posts: 817
  • Let's meet at alternate foods at the break
Re: First build in a while
« Reply #2 on: April 03, 2023, 01:56:58 AM »

I've probably mentioned this in other threads but a double "Third hand" weighted base, with a couple alligator clips can really make things easy in terms of holding wires in place to allow you to use one hand on the soldering iron and the other on the solder itself.

Thanks, Morst. The magnifying, lighted soldering station has a third hand too, but I just used it for tinning wires. So, one clip holds the connector, the other the wire? The wire is set in the cup? I prefer to heat the cup then insert the wire to avoid overheating the wire, so not sure that'd work for me.

I've seen folks mount their iron vertically, then hold component or wire in one hand, solder in the other. Then move things into contact with the iron and apply solder. Thinking that might work best with my style of assembly. Anyone tried that?
« Last Edit: April 03, 2023, 11:24:15 AM by checht »
MK41s, MK22s; Vanguard V1s matched pair
Schoeps kcy5, nbob actives
Naiant PFA 60v, PFA 48v, IPA
Sound Devices MP-6II; Sony PCM-A10

Recordings at LMA

Offline Gutbucket

  • record > listen > revise technique
  • Trade Count: (16)
  • Needs to get out more...
  • *****
  • Posts: 16055
  • Gender: Male
  • We create auditory illusions, not reproductions
Re: First build in a while
« Reply #3 on: April 03, 2023, 12:09:54 PM »
Nice work.

I've seen folks mount their iron vertically, then hold component or wire in one hand, solder in the other. Then move things into contact with the iron and apply solder. Thinking that might work best with my style of assembly. Anyone tried that?

I use this method, with the iron held in a small vice, or lacking that, simply inserted into the center hole of the solder spool.

Quote
Russian winter hat with the ear coverings snapped up
I wore one of those as a Florida kid attending college in upstage NY, driving an old aircooled convertible VW with "rust ventilated" floorboard and no heat.  I never stuck mics in the hat but that's genius.  Extra points if the fur of the hat acted as windjammer!
« Last Edit: April 03, 2023, 03:04:48 PM by Gutbucket »
musical volition > vibrations > voltages > numeric values > voltages > vibrations> virtual teleportation time-machine experience
Better recording made easy - >>Improved PAS table<< | Made excellent- >>click here to download the Oddball Microphone Technique illustrated PDF booklet<< (note: This is a 1st draft, now several years old and in need of revision!  Stay tuned)

Offline fireonshakedwnstreet

  • Trade Count: (8)
  • Taperssection Member
  • ***
  • Posts: 854
  • Gender: Male
  • David
Re: First build in a while
« Reply #4 on: April 03, 2023, 01:31:38 PM »
Very nice. This is def a skill I want to learn!
Mics: AT 3031; Samson C02; Studio Projects C4 (c, o, h); Nak 300/Tascam PE-125/JVC M510 (cp-1, cp-2, cp-3, JVC M510 superdirectional caps)
Recorder: Tascam DR-680 MkII
Pres: Edirol UA-5 (Oade PMod); Marantz PMD661 (OCM); Marantz PMD620 (Oade WMod); Naiant MidBox
https://archive.org/details/@fireonshakedwnstreet

Offline morst

  • I think I found an error on the internet; #UnionStrong
  • Trade Count: (2)
  • Needs to get out more...
  • *****
  • Posts: 6136
Re: First build in a while
« Reply #5 on: April 03, 2023, 02:10:23 PM »
Thanks, Morst. The magnifying, lighted soldering station has a third hand too, but I just used it for tinning wires. So, one clip holds the connector, the other the wire? The wire is set in the cup? I prefer to heat the cup then insert the wire to avoid overheating the wire, so not sure that'd work for me.

I've seen folks mount their iron vertically, then hold component or wire in one hand, solder in the other. Then move things into contact with the iron and apply solder. Thinking that might work best with my style of assembly. Anyone tried that?
dang, I could swear I posted a reply last night to this.


Note that the clips swing around on this thing, so they can hold items in place against the table surface too.
With your vice you only really need a single-clip third hand unit, but they are not very expensive anyhow so I'd suggest the double.
https://toad.social/@morst spoutible.com/morst post.news/@acffhmorst

Offline Gutbucket

  • record > listen > revise technique
  • Trade Count: (16)
  • Needs to get out more...
  • *****
  • Posts: 16055
  • Gender: Male
  • We create auditory illusions, not reproductions
Re: First build in a while
« Reply #6 on: April 03, 2023, 02:54:03 PM »
TS was down earlier this morning, possible some messages may have disappeared due to that.
musical volition > vibrations > voltages > numeric values > voltages > vibrations> virtual teleportation time-machine experience
Better recording made easy - >>Improved PAS table<< | Made excellent- >>click here to download the Oddball Microphone Technique illustrated PDF booklet<< (note: This is a 1st draft, now several years old and in need of revision!  Stay tuned)

Offline voltronic

  • Trade Count: (40)
  • Needs to get out more...
  • *****
  • Posts: 4188
Re: First build in a while
« Reply #7 on: April 03, 2023, 03:00:40 PM »

I've seen folks mount their iron vertically, then hold component or wire in one hand, solder in the other. Then move things into contact with the iron and apply solder. Thinking that might work best with my style of assembly. Anyone tried that?

This won't work with the Pinecil, because it goes into low-temp/power mode when held still for a certain number of seconds. Although this may be an option that can be changed in the settings.
I am hitting my head against the walls, but the walls are giving way.
- Gustav Mahler

Acoustic Recording Techniques
Team Classical
Team Line Audio
Team DPA

Offline morst

  • I think I found an error on the internet; #UnionStrong
  • Trade Count: (2)
  • Needs to get out more...
  • *****
  • Posts: 6136
Re: First build in a while
« Reply #8 on: April 03, 2023, 03:13:18 PM »
TS was down earlier this morning, possible some messages may have disappeared due to that.
thanks. Glad to know that if I'm crazy, that it's not new.
https://toad.social/@morst spoutible.com/morst post.news/@acffhmorst

Offline rocksuitcase

  • Trade Count: (4)
  • Needs to get out more...
  • *****
  • Posts: 8634
  • Gender: Male
    • RockSuitcase: stage photography
Re: First build in a while
« Reply #9 on: April 03, 2023, 03:44:44 PM »
TS was down earlier this morning, possible some messages may have disappeared due to that.
Yeah, I posted on after morst saying to Chris, "looks good, thanks for the pics". That was lost.
sooo
looks good, thanks for the pics              ;D
music IS love

When you get confused, listen to the music play!

Mics:         AKG460|CK61|CK1|CK3|CK8|Beyer M 201E|DPA 4060 SK
Recorders:Marantz PMD661 OADE Concert mod; Tascam DR680 MKI x2; Sony PCM-M10

 

RSS | Mobile
Page created in 0.051 seconds with 34 queries.
© 2002-2024 Taperssection.com
Powered by SMF