Become a Site Supporter and Never see Ads again!

Author Topic: battery and cable to "split" power  (Read 5186 times)

0 Members and 1 Guest are viewing this topic.

Offline Since85

  • Trade Count: (12)
  • Taperssection Regular
  • **
  • Posts: 243
  • Gender: Male
battery and cable to "split" power
« on: July 14, 2019, 02:11:28 PM »
Hi all,

I would like to power a deck and a preamp with ONE battery, and hopefully ONE cable that splits to plug each device (preamp and deck).

The preamp runs on 6 AA batteries (9v), and the deck runs on 6 AA batteries (PMD-661) (6v, but runs on 5 V battery that would charge an iPhone).

Any advice appreciated, thanks in advance!

Online goodcooker

  • Trade Count: (43)
  • Needs to get out more...
  • *****
  • Posts: 4631
  • Gender: Male
  • goes to 11
Re: battery and cable to "split" power
« Reply #1 on: July 14, 2019, 04:07:18 PM »

There are several battery solutions that will put out 9V on one port and 5V on another.

Using a split cable as you describe is impossible without making something with an inline voltage regulator which would be a total pain. You just need to use two appropriate cables from the right battery with two outputs.
Line Audio CM3/OM1 || MBHO KA500 hyper>PFA|| ADK A51 type IV || AKG C522XY
Oade Warm Mod and Presence+ Mod UA5s || Aerco MP2(needs help) || Neve Portico 5012 || Apogee MMP
SD Mixpre6 || Oade Concert Mod DR100mkii

pocket sized - CA11 cards > SP SB10 > Sony PCM A10

http://www.archive.org/bookmarks/goodcooker

"Are you the Zman?" - fan at Panic 10-08-10 Kansas City
"I don't know who left this perfectly good inflatable wook doll here, but if I'm blowing her up, I'm keeping her." -  hoppedup

Offline old and in the way

  • Trade Count: (0)
  • Taperssection Regular
  • **
  • Posts: 194
Re: battery and cable to "split" power
« Reply #2 on: July 14, 2019, 04:17:07 PM »
There are distribution boxes (Audioroot ) makes a few but you would need to regulate the power to the lower voltage device. an inline voltage regulator.

Offline jeenash

  • Trade Count: (4)
  • Taperssection Regular
  • **
  • Posts: 139
  • Gender: Male
Re: battery and cable to "split" power
« Reply #3 on: July 14, 2019, 04:38:22 PM »
Try one of these. Has 12v 9v and USB 5v ports. Runs a mixpre 3 longer than I've ever needed. TalentCell Rechargeable 72W 100WH 12V/8300mAh 9V/11000mAh 5V/20000mAh DC Output Lithium Ion Battery Pack for LED Strip and CCTV Camera, Portable Li-ion Power Bank, Black https://www.amazon.com/dp/B01337QXMA/ref=cm_sw_r_other_apa_i_yh5kDbHXRHT5M

Offline Since85

  • Trade Count: (12)
  • Taperssection Regular
  • **
  • Posts: 243
  • Gender: Male
Re: battery and cable to "split" power
« Reply #4 on: July 14, 2019, 05:28:55 PM »
Try one of these. Has 12v 9v and USB 5v ports. Runs a mixpre 3 longer than I've ever needed. TalentCell Rechargeable 72W 100WH 12V/8300mAh 9V/11000mAh 5V/20000mAh DC Output Lithium Ion Battery Pack for LED Strip and CCTV Camera, Portable Li-ion Power Bank, Black https://www.amazon.com/dp/B01337QXMA/ref=cm_sw_r_other_apa_i_yh5kDbHXRHT5M

Very helpful, thank you. So Two cables would come out of this, one to power preamp, and the other to power recorder?
Who have you used to make power cables?

Thanks again!

Offline jeenash

  • Trade Count: (4)
  • Taperssection Regular
  • **
  • Posts: 139
  • Gender: Male
Re: battery and cable to "split" power
« Reply #5 on: July 14, 2019, 05:46:16 PM »
Yep 2 separate cables. I make my own but there are others here that do it as a side gig and can help you with that. If you can figure out the jack size, you may be able to find it online.

 

RSS | Mobile
Page created in 0.047 seconds with 35 queries.
© 2002-2024 Taperssection.com
Powered by SMF