Become a Site Supporter and Never see Ads again!
« previous next »
Pages: 1 [2]  All   Go Down

Author Topic: Recommendations for an ultra-wide T-Bar for omni's?  (Read 4817 times)

0 Members and 1 Guest are viewing this topic.

Offline silentmark

  • Shine with or without cherries ?
  • Trade Count: (5)
  • Needs to get out more...
  • *****
  • Posts: 2685
  • Gender: Male
  • Boat, cucumber, wire ...
Re: Recommendations for an ultra-wide T-Bar for omni's?
« Reply #15 on: June 16, 2004, 03:34:35 PM »
Take a hockey stick and cut the blade off, trim to desired spread, drill a hole in the center to place on stand, secure with duct tape or velcro, etc ., add a clamp on either end, works like a charm ...

Setup is far right in the photo ...
« Last Edit: June 16, 2004, 03:36:23 PM by silentmark »
Logged
Dissent is the highest form of patriotism. - Howard Zinn, not Thomas Jefferson ...

Mics: Neumann AK50/AK40/AK30/AK20(1 for M/S), AKG568eb's (gathering dust)
Decks: R-44 (OCM), Fostex FR2LE (OWM), Microtacker (semi-retired), D8 (retired), D7 (retired)
Pre-amps: Apogee Minime (semi-retired), Sonosax SX-M2 (semi-retired), Oade mod SBM-1 (retired)
Cables: LC3 actives (older lemo style x2), Audio Magic Hyper Conductor interconnects

http://www.youtube.com/watch?v=J3qrWOOposQ

Offline John Kelly

  • Been a while...
  • Trade Count: (1)
  • Needs to get out more...
  • *****
  • Posts: 9753
  • Gender: Male
    • The Jokell
Re: Recommendations for an ultra-wide T-Bar for omni's?
« Reply #16 on: June 16, 2004, 03:47:04 PM »
Quote from: silentmark on June 16, 2004, 03:34:35 PM
Take a hockey stick and cut the blade off, trim to desired spread, drill a hole in the center to place on stand, secure with duct tape or velcro, etc ., add a clamp on either end, works like a charm ...

Setup is far right in the photo ...

Actually that's very similar to a friend of mine's setup.  He had a long piece of wood with a stand adapter in the middle.  He put some velcro on it and ran dpa4060s on it.  Made some great tapes...
Logged
Sennheiser MKH8040st > SD 702
XBL/PSN/Steam ID: thejokell

Offline §†∑∫åµÞ≥¥

  • You can call me Steve.
  • Trade Count: (2)
  • Needs to get out more...
  • *****
  • Posts: 7105
  • Gender: Male
Re: Recommendations for an ultra-wide T-Bar for omni's?
« Reply #17 on: June 16, 2004, 04:17:04 PM »
Quote from: silentmark on June 16, 2004, 03:34:35 PM
Take a hockey stick and cut the blade off, trim to desired spread, drill a hole in the center to place on stand, secure with duct tape or velcro, etc ., add a clamp on either end, works like a charm ...

Setup is far right in the photo ...

Great idea!! Thanks. :)
Logged
"Absurdity is the only reality." - FZ

LMA recordings
www.nutritionbulk.com
Pages: 1 [2]  All   Go Up
« previous next »
 

RSS | Mobile
Page created in 0.049 seconds with 32 queries.
© 2002-2024 Taperssection.com
Powered by SMF