« Reply #29 on: February 03, 2007, 06:03:20 PM »
Well from what I have seen if the Nady is the same on the inside it could benefit from changing all the resistors to metal film and all 1% values because 5% does not cut it for me... This will help balance out the left and right sides and bring the noise floor down. The Tantalum coupling caps have to go... and get replaced with Mylar then I would take a good look at the electrolytics and see if they can be changed out for a better quality cap.. After that I would take a look at the opamps for a burr brown substitute that could be used current draw would obviously be a huge factor here. I would then take a huge look at the cheesy 1$ pots they are using and maybe replace them with a rotary 12 position pot with precision resistors on it. Then I would rip out that diode limiter peace of turd and use the switch for a high pass filter... that might be tricky you would probably have to put in a small sub board with the HPF caps on it. and swap them out for the coupling caps ether in the input ( preferred method ) or somewhere close the the first stage. But again in order to figure the cap out you need to figure out the source impedance of the circuit ( that's not something I can figure out ) or anyone with out a schematic.. So trial and error with a MLS analyzer could show what the cap is doing..
Then after that you might have a pretty good preamp or at least as good as it could be... They are using a SIX hex inverter hex chip to get the 48v or so voltage but I think max current is only going to be 12mA I suspected they were cascading inverters some how. So that's a pretty good chip they may be better ones that will drop in The chip is a TC4069UBP its a Toshiba chip here is the data sheet for it. I think that they must "split" of the supply and then use a virtual ground and create a + and - supply for the opamps.
http://www.datasheetcatalog.com/datasheets_pdf/T/C/4/0/TC4069UBP.shtml
Great diagnosis, Chris.
So what are those four transistors used for? Is that part of the limiter circuit?
OK, it looks like they are using the TL074 chip for a preamp. That is easily replaceable with any (FET input) opamp, right?
Richard
Yes the transistors are for the limiter. Its a way of ramping up the signal to drive the diodes hard enough to get them to clamp down lol its pretty lame. We are not talking state of the art here more state of the FART...
I would get rid of the tl074 that's a real dinosaur of an opamp anything by burr brown would smoke it. I will check out substitutions based on chip size ect.. And see what we can come up with THAT corporation also makes really good opamps I am going to be designing a full sized stereo preamp based on the THAT chip the 1503 or something I forget the name but its a very good chip very easy to make a good preamp out of.
Nice plan. You're talking about the THAT 1510/1512. Those are replacement for TI INA217, which are replacements for AD SSM2017/19. All nice chips, that's for sure. They are what is inside the DMIC-20. They use a boost circuit to get from +6V to +/-12V. Theirs is an inductor-based one (Maxim 743), but you can also use "charge pumps" (LT1054) to do it too. I actually started breadboarding this before I started buying (and hacking) so much gear. And now I've just bought an Edirol R09
. When will it end. Someone save me from myself!
Richard
Logged
Mics: Sennheiser MKE2002 (dummy head), Studio Projects C4, AT825 (unmodded), AT822 franken mic (x2), AT853(hc,c,sc,o), Senn. MKE2, Senn MKE40, Shure MX183/5, CA Cards, homebrew Panasonic and Transsound capsules.
Pre/ADC: Presonus Firepod & Firebox, DMIC20(x2), UA5(poorly-modded, AD8620+AD8512opamps), VX440
Recorders: Edirol R4, R09, IBM X24 laptop, NJB3(x2), HiMD(x2), MD(1).
** This individual has moved to user "illconditioned" **