Become a Site Supporter and Never see Ads again!
Previous topic - Next topic
Pages: Pages1   Go Down

Author Topic: DIY 9volts battery box  (Read 3,976 times)

0 Members and 1 Guest are viewing this topic.

Offline one8ung

  • Trade Count: (5)
  • Taperssection Member
  • ***
  • Posts: 365
DIY 9volts battery box
« on: December 07, 2025, 07:27:39 AM »
9volts battery box creation...
Logged
Mics: DPA 4061

Power: CA-UBB, Custom made battery box(es)

Recorders: Deity PR-2, Tascam DR-2d (3x)

Field mixer, interface: Teenage Engineering TX-6, RØDE AI-Micro (2x)

IEM Receivers: Sennheiser EK 2000 IEM-Aw, Sennheiser EK 2000 IEM-Bw, Sennheiser EK 2000 IEM-GBw, Sennheiser EK 2000 IEM-Gw, Shure ADXR, Shure P10R G10, Shure P10R+ J8e, Shure P10R L8, Wisycom MPR50-IEM

Offline robgronotte

  • Trade Count: (0)
  • Taperssection Member
  • ***
  • Posts: 510
Re: DIY 9volts battery box
« Reply #1 on: December 07, 2025, 09:56:41 AM »
What are all the pieces you used?
Logged

Offline one8ung

  • Trade Count: (5)
  • Taperssection Member
  • ***
  • Posts: 365
Re: DIY 9volts battery box
« Reply #2 on: December 07, 2025, 10:23:34 AM »
Quote from: robgronotte on December 07, 2025, 09:56:41 AM
What are all the pieces you used?

-Circuit board
-Two resistors
-Two capacitors
-One 1/8" / 3.5mm stereo jack
-One cable with a 1/8" / 3.5mm stereo plug
-One Battery holder for 1 9V battery
Logged
Mics: DPA 4061

Power: CA-UBB, Custom made battery box(es)

Recorders: Deity PR-2, Tascam DR-2d (3x)

Field mixer, interface: Teenage Engineering TX-6, RØDE AI-Micro (2x)

IEM Receivers: Sennheiser EK 2000 IEM-Aw, Sennheiser EK 2000 IEM-Bw, Sennheiser EK 2000 IEM-GBw, Sennheiser EK 2000 IEM-Gw, Shure ADXR, Shure P10R G10, Shure P10R+ J8e, Shure P10R L8, Wisycom MPR50-IEM

Offline lpmaskman

  • Trade Count: (0)
  • Taperssection Regular
  • **
  • Posts: 156
    • Trade list
Re: DIY 9volts battery box
« Reply #3 on: December 13, 2025, 04:59:23 PM »
Quote from: one8ung on December 07, 2025, 10:23:34 AM
Quote from: robgronotte on December 07, 2025, 09:56:41 AM
What are all the pieces you used?

-Circuit board
-Two resistors
-Two capacitors
-One 1/8" / 3.5mm stereo jack
-One cable with a 1/8" / 3.5mm stereo plug
-One Battery holder for 1 9V battery
What was the material for the black foil cover?
Logged
Mics: AT853, ATM35, RODE Videomic Go, MIC-109, Panasonic WM-61A
Mic power: 3-wire battery boxes, 4.7kOhm mod cable, CA9100
Recorders: Deity PR-2, Olympus LS-12, Zoom H2 (4 channel line input mod), Instamic Pro Plus C Stereo
Video/photo: Panasonic HC-V770, Panasonic HC-VX1, Sony RX10mkII, Sony RX100mkIV, Sony FDR-AX53, GoPro Hero4 Silver

https://www.facebook.com/lawrencelivevids - Concert videography and photography
http://xdespisedkidx.bplaced.net/ - trade site

Offline one8ung

  • Trade Count: (5)
  • Taperssection Member
  • ***
  • Posts: 365
Re: DIY 9volts battery box
« Reply #4 on: December 14, 2025, 09:32:55 PM »
Quote from: lpmaskman on December 13, 2025, 04:59:23 PM

What was the material for the black foil cover?


That is hot melt glue that you melt with a hot melt glue gun.

https://www.youtube.com/watch?v=UofY6lOQ-q0

Logged
Mics: DPA 4061

Power: CA-UBB, Custom made battery box(es)

Recorders: Deity PR-2, Tascam DR-2d (3x)

Field mixer, interface: Teenage Engineering TX-6, RØDE AI-Micro (2x)

IEM Receivers: Sennheiser EK 2000 IEM-Aw, Sennheiser EK 2000 IEM-Bw, Sennheiser EK 2000 IEM-GBw, Sennheiser EK 2000 IEM-Gw, Shure ADXR, Shure P10R G10, Shure P10R+ J8e, Shure P10R L8, Wisycom MPR50-IEM
Pages: Pages1   Go Up
Previous topic - Next topic
 

RSS | Mobile
Page created in 0.086 seconds with 31 queries.
© 2002-2026 Taperssection.com
Powered by SMF