Become a Site Supporter and Never see Ads again!
« previous next »
Pages: [1]   Go Down

Author Topic: channels switching on a JB3? any help?  (Read 1690 times)

0 Members and 1 Guest are viewing this topic.

Offline jagraham

  • Trade Count: (20)
  • Needs to get out more...
  • *****
  • Posts: 3002
  • Gender: Male
channels switching on a JB3? any help?
« on: July 10, 2008, 11:36:18 AM »
im recording with CA cards > CA-9000 Pre > JB3.  i cannot for the life of me figure out which of the mics is left and which is right because if i turn the JB3 off after everything is set up the channels switch.  i dont know if it is the recorder or the mics/pre.  im sure there is an explanation for this but i have no idea.  anyone have any experience with a similar setup and know what the issue might be?  thanks in advance.
Logged
Mics: Nak CM-300s, Nak CM-100s, CP-1s, CP-2s, AT-853s(Cards, Hypers, Omnis) CA-14s(Cards, Omnis)
Pres: CA STC-9200, CA-UBB
Recorders: Tascam DR-70D, DR-2D, Edirol R-09

ISO: 1 Teac ME-120, CP-3 Caps, AT-853 Subcard Caps

Offline bhtoque

  • Trade Count: (3)
  • Needs to get out more...
  • *****
  • Posts: 3308
  • Gender: Male
  • So much music, so little time.
Re: channels switching on a JB3? any help?
« Reply #1 on: July 11, 2008, 01:05:10 AM »
Quote from: jagraham on July 10, 2008, 11:36:18 AM
im recording with CA cards > CA-9000 Pre > JB3.  i cannot for the life of me figure out which of the mics is left and which is right because if i turn the JB3 off after everything is set up the channels switch.  i dont know if it is the recorder or the mics/pre.  im sure there is an explanation for this but i have no idea.  anyone have any experience with a similar setup and know what the issue might be?  thanks in advance.

The JB3 switches channels every time you pause/stop a recording. I used to just tag the right channel by speaking into the mic when I dropped my stand.

JAson
Logged
MG 200/210/270
AKG c422>s42>Hydra silver interconnects
AKG 391/92/93>MK 90/3 actives
>AM Hyper-Conductors
Studio Projects LSD2>MiAGi II
>Edirol R-4 (Oade T Mod)

db.etree.org/bhtoque

Offline sunjan

  • Trade Count: (0)
  • Needs to get out more...
  • *****
  • Posts: 2006
  • Gender: Male
  • Taping since 1988, 28 years of fine recordings...
    • Just a handful of stuff I put on etree
Re: channels switching on a JB3? any help?
« Reply #2 on: July 20, 2008, 10:20:52 AM »
Quote from: jagraham on July 10, 2008, 11:36:18 AM
im recording with CA cards > CA-9000 Pre > JB3.  i cannot for the life of me figure out which of the mics is left and which is right because if i turn the JB3 off after everything is set up the channels switch.  i dont know if it is the recorder or the mics/pre.  im sure there is an explanation for this but i have no idea.  anyone have any experience with a similar setup and know what the issue might be?  thanks in advance.

This is a known bug with the JB3.  :( It's in the FAQ, IIRC...
Nothing you can do about it, other than reversing the channels in post if it bothers you.

Logged
Mics: A-51s LE, CK 930, Line Audo CM3, AT853Rx (hc,c,sc),  ECM 121, ECM 909A
Pres: Tinybox, CA-9100, UA5 wmod
Recorders: M10, H116 (CF mod), H340, NJB3
Gearbag: High Sierra Corkscrew
MD transfers: MZ-RH1. Tape transfers: Nak DR-1
Photo rig: Nikon D70, 18-70mm/3.5-4.5, SB-800
Pages: [1]   Go Up
« previous next »
 

RSS | Mobile
Page created in 0.039 seconds with 27 queries.
© 2002-2024 Taperssection.com
Powered by SMF