I assume you've installed the latest drivers?

And this alone is a problem:

Quote from: gloco on January 14, 2004, 05:44:07 PM
I ran a coax cable from the optical out to the spdif in on the extension cable that comes with the card

You can't run a coax cable from an optical output.  Make sure all your connections are properlly set up - i.e. coax to coax, optical to optical.

Quote from: Brian Skalinder on January 14, 2004, 05:47:12 PM
I assume you've installed the latest drivers?

grabbing it now, hopefully this will do it

Quote from: Brian Skalinder on January 14, 2004, 06:04:37 PM

Quote from: gloco on January 14, 2004, 05:50:51 PM
jeepers creepers.  So i need an optical>spdif cable then eh?  But i don't get something, everywhere i check they state the optical i/o is spdif, so...i'm not sure what's wrong then.

The two primary types of cables across which consumer digital signals (S/PDIF) are sent are:

[1] coax
[2] optical

Coax cables transmit electrical signals.  Optical cables transmit light signals.  I do not know of any such thing as a coax > optical cable.  In order to convert from one format to the other (i.e coax > optical, or optical > coax), you need a digital format converter of some kind (several listed here).

From the specs, though, it looks to me like the Echo MiaMIDI supports inputting a coax S/PDIF signal.  And if the DA-20 specs are the same as the DA-20mkII, then it should support outputting a coax S/PDIF signal.  If this is the case, all you need is a 75-ohm coaxial cable with RCA connectors to connect the two machines.  Even Radio Shack has reasonably good quality 75-ohm coaxial cables with RCA connectors.

Hey Brian, thanks for the input.  Looks like i'm going to need one of these converter boxes, i already picked up the coax cable with rca connectors from jandr a few days back, unfortunately it didn't state what the ohm's were for the cable anywhere on the packaging, this cable did work when i plugged in coax out from my dvd deck>optical rca in to the deck.  Maybe it's not that easy for the soundcard i suppose.

Quote from: Brian Skalinder on January 14, 2004, 06:16:29 PM

Quote from: gloco on January 14, 2004, 06:10:57 PM
i already picked up the coax cable with rca connectors from jandr a few days back, unfortunately it didn't state what the ohm's were for the cable anywhere on the packaging

If the packaging said it's a "digital" cable, it's 75-ohms.

Quote from: gloco on January 14, 2004, 06:10:57 PMthis cable did work when i plugged in coax out from my dvd deck>optical rca in to the deck.

Impossible.  You cannot run a coax output from your DVD into an optical input on your DAT deck without a digital format converter of some kind.  I suspect you actually did this:

DVD deck RCA/coax output > RCA/coax input on DAT deck

You just want to do the same thing with your DAT and soundcard, now:

DAT deck RCA/coax output > RCA/coax input on MiaMIDI

Once you have these two devices hooked up properly - and the drivers updated and your software configured correctly - you should be able to transfer from DAT > PC.

Ok, so my assumption is that the software is not setup then because i did run the cable from the coax out to the coax in on my soundcard.  My soundcard has this external attachment which has the spdif's on it.  

I typically use cd wave to do the recording, i also have adobe audition.  My issue is that i do not see a spdif option in the Sound and Audio devices properties.  I did download the latest drives and restarted the pc...oh the cable was marked "digital" so that sounds right.  I think i'm missing a big step regarding setting up the spdif in the software and i'm clueless as to what else i need to do.  Thanks again  

Quote from: Brian Skalinder on January 14, 2004, 06:30:29 PM
What OS are you running - WinXP?

Ah yes, XP.  

Quote from: Brian Skalinder on January 14, 2004, 06:44:23 PM
[1] Open your Computer Management Console - go to Start | Settings | Control Panel | Admin Tools | Computer Management.
[2] Within the CMC, click the Device Manager node on the left.
[3] Expand the Sound, Video and Game Controllers node on the right
[4] Find your Echo MiaMIDI in the device list (may be more than one entry)
[5] For each entry in [4], right-click the Echo MiaMIDI and verify the Device Status reads something like "This device is working properly."

Respond back here with:

[a] which Echo devices are in the list
their status, i.e. working properly or some kind of conflict

Ok, here's the list:

Audio Codecs
Legacy Audio Drivers
Legacy Video Capture Devices
Media Control Devices
Mia (WDM)
Video Codecs

I check everything and they are all working properly.  Thanks again!

Quote from: Schwilly on January 15, 2004, 12:07:35 AM
I'm all confused here, there should be no cable/signal type problems running DA-20 coax to echo coax

with soundcards, there is usually an icon in the system tray where you can access the properties of the soundcard.  Try toggling the consumer/pro signal buttons and the the digital input type (coax/optical).  If the software is worth a damn it should tell you when the 2 digital devices are locked on to each other.

    Ya telling me, i figured this should be a breeze.  What's pissing me off is that i cannot view the spdif properties when i pull up the full sized volume box (which has the lever for volume and balance levels).  Spdif is simply not listed on playback and recording, it's driving me mad thinking about it.  And another thing...the damn card did not have a manual with it!  I went to echo's site and downloaded it, when i get home from work i'm gonna read it but i doubt it's going to offer any explanation.  

    What's odd is that when i first opened up the console software for the card i heard some buzzing and saw the digital in meters bouncing around, when i clicked analog then spdif input again the meters shot all the way up and stayed there and the buzzing stopped.  Beyond me what the hell is wrong with this thing.  Again, it's gotta be software, something isn't letting me access the spdif i/o.  Hopefully i'll get it figured out soon as i got some shows coming up.