My SRS 3D printed microphone bars

[noahbickart]

https://www.shapeways.com/product/W5BGSBPST/hybrid-schoeps-nbobs?li=shareProduct
Newest Bar, meant for OTS PAS taping with 60° angles. 21cm for the mk41v and 30cm for the mk22 (Stereophonic zoom used to match Cardioids in DIN Recording angle, with the different capsules and angles). This bar can accommodate big windscreens for outdoor use. 

https://www.shapeways.com/product/WLTJKUU2H/din-nos-combo-mount?optionId=60523604
DIN/NOS Combo Mount for Schoeps with NBob active cables. Upper pair (20cm) for side-address capsules. Lower pair (30cm @ 90°) for end-address capsules.

https://www.shapeways.com/product/MPPBSUT26/ms-xy-schoeps-with-nbob-actives?optionId=60409239
X/Y or M/S for Schoeps vertical capsules.

https://www.shapeways.com/product/DQ3TZRTAK/hybrid-schoeps-w-n-bob-actives?optionId=60996905
Mounts for 3 Pairs of Schoeps. Outside pair: 70 degrees 35 cm (for the mk22, essentially the same Recording angle as Cards NOS, but modified using the stereophonic zoom for narrower angle and the mk22), plus two vertical pairs, at 30 cm
and 20 cm. This bar is for indoors only, and can not accommodate big windscreens for outdoor use.

[dactylus]

Nice bars Noah!  I think that I'm going to pick up the newest bar that you posted for my mk22's & mk4V's.

[noahbickart]

Nice bars Noah!  I think that I'm going to pick up the newest bar that you posted for my mk22's & mk4V's.

That bar was designed for the mk41v but would likely work with the 4v as well.

I'm going to run mk22 and mk41v pairs on that bar along with a mk4v/mk8 M/S rig on Sunday at Phish

[fobstl]

The bars that Scott is creating are truly awesome. I currently have him working on a Kangol mount that looks like it is going to be pretty cool.

[LiveOnTape]

https://www.shapeways.com/product/MPPBSUT26/ms-xy-schoeps-with-nbob-actives?optionId=60409239
X/Y or M/S for Schoeps vertical capsules.

The M/S clip looks really cool.  Do you know the size of the clips for nBobs?  I use two AKG M90 active cables with CK94 figure 8 caps for MS/Blumline.  They look very similar, and have a 12mm clip.  Would this fit?  or do you do custom orders to make one that does? 

Also, are those just small clips back to back with 20mm clip, then just a 20mm post (three pieces)?  If so, I can see these being used in my double M/S rig where I want to use a back-to-back clip onto the AKG's 19mm body (facing backwards). 

Great work,
L

[dactylus]

Nice bars Noah!  I think that I'm going to pick up the newest bar that you posted for my mk22's & mk4V's.

That bar was designed for the mk41v but would likely work with the 4v as well.

I'm going to run mk22 and mk41v pairs on that bar along with a mk4v/mk8 M/S rig on Sunday at Phish

Yes, I saw that you had the bar constructed for mk41v's but it should also be effective for the mk4v's that I run.

[dactylus]

I'm going to run mk22 and mk41v pairs on that bar along with a mk4v/mk8 M/S rig on Sunday at Phish

It will be interesting to hear the mk4v/mk8 M/S rig in action.  Have a good time this evening!

[acidjack]

The bars that Scott is creating are truly awesome. I currently have him working on a Kangol mount that looks like it is going to be pretty cool.

Could you please remember to post that when it's done? Or if there's a place to buy one now, I'd love a link...

[dactylus]

I'm going to run mk22 and mk41v pairs on that bar along with a mk4v/mk8 M/S rig on Sunday at Phish

It will be interesting to hear the mk4v/mk8 M/S rig in action.  Have a good time this evening!

Noah did you decide to run the mk4v/mk8 M/S rig at a future show?

[noahbickart]

I'm going to run mk22 and mk41v pairs on that bar along with a mk4v/mk8 M/S rig on Sunday at Phish

It will be interesting to hear the mk4v/mk8 M/S rig in action.  Have a good time this evening!

Noah did you decide to run the mk4v/mk8 M/S rig at a future show?

I ran the 4v pair again last night. The bar was heavy enough and I didn't feel like doing an extra clamp and mount for m/s. Sorry

[fobstl]

The bars that Scott is creating are truly awesome. I currently have him working on a Kangol mount that looks like it is going to be pretty cool.

Could you please remember to post that when it's done? Or if there's a place to buy one now, I'd love a link...

Yes, Scott is sending me his second prototype to review. Once we have it finalized I will let everyone know.

[dactylus]

I'm going to run mk22 and mk41v pairs on that bar along with a mk4v/mk8 M/S rig on Sunday at Phish

It will be interesting to hear the mk4v/mk8 M/S rig in action.  Have a good time this evening!

Noah did you decide to run the mk4v/mk8 M/S rig at a future show?

I ran the 4v pair again last night. The bar was heavy enough and I didn't feel like doing an extra clamp and mount for m/s. Sorry

Thanks Noah!  I understand completely.  Do you have any recordings posted using your mk4v/mk8 M/S rig?  I'd love to hear how that setup sounds.

[F.O.Bean]

Here's the [3] SRS 4 Channel Mounts that I have too! I HIGHLY recommend these to ANYONE who wants to run 2+ Channels and do it very lightweight ALL of my capsules are VERTICALLY ALIGNED, and because of that, I can easily mix the multi mic configs for a 4 Channel Matrix, IF the tapes came out good enough

DINa/DIN
https://www.shapeways.com/product/J5WZFJ324/dina-din-combo?optionId=60350415

DINa/ORTF
https://www.shapeways.com/product/EARVGAFW3/dina-ortf-combo?li=shareProduct

DINa/NOS
https://www.shapeways.com/product/DU5BBY7BA/dina-nos-combo?optionId=60421670

And Noah, thanks for all of your hard work @MSG

[noahbickart]

Bean:

I really encourage you to experiment with narrower angles and wider spacings. Your bars are all 110 or 90 degrees, which work great for FOB on on stage, but from the OTS, there's too little direct sound compared with too much reflected sound and crowd noise.

Here's the [3] SRS 4 Channel Mounts that I have too! I HIGHLY recommend these to ANYONE who wants to run 2+ Channels and do it very lightweight ALL of my capsules are VERTICALLY ALIGNED, and because of that, I can easily mix the multi mic configs for a 4 Channel Matrix, IF the tapes came out good enough

DINa/DIN
https://www.shapeways.com/product/J5WZFJ324/dina-din-combo?optionId=60350415

DINa/ORTF
https://www.shapeways.com/product/EARVGAFW3/dina-ortf-combo?li=shareProduct

DINa/NOS
https://www.shapeways.com/product/DU5BBY7BA/dina-nos-combo?optionId=60421670

And Noah, thanks for all of your hard work @MSG

[noahbickart]

Nice bars Noah!  I think that I'm going to pick up the newest bar that you posted for my mk22's & mk4V's.

That bar was designed for the mk41v but would likely work with the 4v as well.

I'm going to run mk22 and mk41v pairs on that bar along with a mk4v/mk8 M/S rig on Sunday at Phish

Yes, I saw that you had the bar constructed for mk41v's but it should also be effective for the mk4v's that I run.

I used the mk4v in this mount along with the mk22. Check them out:

mk22 16bit: http://bt.etree.org/details.php?id=594985
mk22 24bit: http://bt.etree.org/details.php?id=595004

mk4v 16bit: http://bt.etree.org/details.php?id=595006
mk4v 24bit: http://bt.etree.org/details.php?id=595005