Become a Site Supporter and Never see Ads again!
« previous next »
Pages: [1]   Go Down

Author Topic: DPA microdot to 3,5mm jack  (Read 5682 times)

0 Members and 1 Guest are viewing this topic.

Offline one8ung

  • Trade Count: (5)
  • Taperssection Member
  • ***
  • Posts: 339
  • Gender: Male
DPA microdot to 3,5mm jack
« on: July 25, 2019, 02:44:12 AM »
Maybe a stupid question but can i replace 2 DPA microdot connectors for 1 3,5mm jack?
« Last Edit: July 25, 2019, 08:57:29 AM by one8ung »
Logged
Mics: DPA 4061, Schoeps CCM 41 Power: CA-UBB Recorders: Deity PR-2, Tascam DR-2d (3x), ZOOM F3

IEM Receivers: Sennheiser EK 2000 IEM-Aw, Sennheiser EK 2000 IEM-Bw, Sennheiser EK 2000 IEM-GBw, Sennheiser EK 2000 IEM-Gw, Sennheiser EK IEM G4-B, Shure P10R G10, Shure P10R J8, Shure P10R L8, Wisycom MPR50-IEM

Offline one8ung

  • Trade Count: (5)
  • Taperssection Member
  • ***
  • Posts: 339
  • Gender: Male
Re: DPA microdot to 3,5mm jack
« Reply #1 on: July 25, 2019, 09:05:54 AM »
To clarify... I want to power 2 DPA microphones with a microdot connector with a Church Audio Ugly Battery Box.

Is this possible?
Logged
Mics: DPA 4061, Schoeps CCM 41 Power: CA-UBB Recorders: Deity PR-2, Tascam DR-2d (3x), ZOOM F3

IEM Receivers: Sennheiser EK 2000 IEM-Aw, Sennheiser EK 2000 IEM-Bw, Sennheiser EK 2000 IEM-GBw, Sennheiser EK 2000 IEM-Gw, Sennheiser EK IEM G4-B, Shure P10R G10, Shure P10R J8, Shure P10R L8, Wisycom MPR50-IEM

Offline tungstengruvsten

  • Trade Count: (4)
  • Taperssection Regular
  • **
  • Posts: 51
  • I'm a llama!
Re: DPA microdot to 3,5mm jack
« Reply #2 on: July 25, 2019, 09:20:32 AM »
Absolutely it can be done.   Cut off the microdots and solder to a 3.5mm jack and you are good to go. 

1/8" or 3.5mm jacks are TRS - Tip/Ring/Sleeve - The ground wires go together and connect to the sleeve, the inner cable from the right mic becomes your Ring and the inner cable from the left mic becomes your Tip.   Heatshrink keeps it together.  You might not want to do it yourself as those DPA wires are incredibly delicate and a real pain to strip cleanly and solder....but it can be done!
Logged

Offline acidjack

  • Site Supporter
  • Trade Count: (37)
  • Needs to get out more...
  • *
  • Posts: 5845
  • Gender: Male
Re: DPA microdot to 3,5mm jack
« Reply #3 on: July 25, 2019, 01:47:15 PM »
DPA can probably do this for you, if you want. I just had a 4061 w/ TA4F reterminated to microdot.
Logged
Mics: Schoeps MK4V, MK41V, MK5, MK22> CMC6, KCY 250/5, KC5, NBob; MBHO MBP603/KA200N, AT 3031, DPA 4061 w/ d:vice, Naiant X-X, AT 853c, shotgun, Nak300
Pres/Power: Aerco MP2, tinybox v2  [KCY], CA-UBB
Decks: Sound Devices MixPre 6, Zoom F8, M10, D50

My recordings on nyctaper.com: http://www.nyctaper.com/?tag=acidjack | LMA: http://www.archive.org/bookmarks/acidjack | twitter: http://www.twitter.com/acidjacknyc | Soundcloud: https://soundcloud.com/acidjacknyc

Offline one8ung

  • Trade Count: (5)
  • Taperssection Member
  • ***
  • Posts: 339
  • Gender: Male
Re: DPA microdot to 3,5mm jack
« Reply #4 on: July 25, 2019, 09:06:20 PM »
Logged
Mics: DPA 4061, Schoeps CCM 41 Power: CA-UBB Recorders: Deity PR-2, Tascam DR-2d (3x), ZOOM F3

IEM Receivers: Sennheiser EK 2000 IEM-Aw, Sennheiser EK 2000 IEM-Bw, Sennheiser EK 2000 IEM-GBw, Sennheiser EK 2000 IEM-Gw, Sennheiser EK IEM G4-B, Shure P10R G10, Shure P10R J8, Shure P10R L8, Wisycom MPR50-IEM

Offline Ziggz

  • Trade Count: (12)
  • Taperssection Member
  • ***
  • Posts: 479
Re: DPA microdot to 3,5mm jack
« Reply #5 on: August 11, 2019, 05:34:35 AM »
Logged
Pages: [1]   Go Up
« previous next »
 

RSS | Mobile
Page created in 0.036 seconds with 29 queries.
© 2002-2025 Taperssection.com
Powered by SMF