Become a Site Supporter and Never see Ads again!
« previous next »
Pages: [1]   Go Down

Author Topic: iRiver 120 torx driver size?  (Read 3659 times)

0 Members and 1 Guest are viewing this topic.

Offline SmokinJoe

  • Trade Count: (63)
  • Needs to get out more...
  • *****
  • Posts: 4212
  • Gender: Male
  • "75 and sunny"... life is so much simpler.
    • uploads to archive.org
iRiver 120 torx driver size?
« on: August 13, 2007, 10:36:46 PM »
I need to pull apart an iriver, which I presume starts by removing those tiny screws.  I've read it's a T5 screw, but I've got a T5 bit, and it's WAY too big.  These things are tiny.  Any idea what the correct size is?
Logged
Mics: Schoeps MK4 & CMC5's / Gefell M200's & M210's / ADK-TL / DPA4061's
Pres: V3 / ST9100
Decks: Oade Concert Mod R4Pro / R09 / R05
Photo: Nikon D700's, 2.8 Zooms, and Zeiss primes
Playback: Raspberry Pi > Modi2 Uber > Magni2 > HD650

Offline Javier Cinakowski

  • !! Downhill From Here !!
  • Trade Count: (11)
  • Needs to get out more...
  • *****
  • Posts: 4325
  • Gender: Male
Re: iRiver 120 torx driver size?
« Reply #1 on: August 13, 2007, 10:43:58 PM »
torx 5.  sears carries it.  torx 5 is freaking tiny....
Logged
Neumann KM185mp OR DPA ST2015-> Grace Design Lunatec V2-> Tascam DR-100mkIII

Offline SmokinJoe

  • Trade Count: (63)
  • Needs to get out more...
  • *****
  • Posts: 4212
  • Gender: Male
  • "75 and sunny"... life is so much simpler.
    • uploads to archive.org
Re: iRiver 120 torx driver size?
« Reply #2 on: August 13, 2007, 11:03:48 PM »
OK, I'm sure you're right.  Now that I look again, the one I have is a T15.  I'll look for a T5 tomorrow.
Logged
Mics: Schoeps MK4 & CMC5's / Gefell M200's & M210's / ADK-TL / DPA4061's
Pres: V3 / ST9100
Decks: Oade Concert Mod R4Pro / R09 / R05
Photo: Nikon D700's, 2.8 Zooms, and Zeiss primes
Playback: Raspberry Pi > Modi2 Uber > Magni2 > HD650

Offline Arni99

  • Trade Count: (0)
  • Taperssection Member
  • ***
  • Posts: 770
  • Gender: Male
Re: iRiver 120 torx driver size?
« Reply #3 on: August 14, 2007, 08:44:30 AM »
i only got a torx 6 which is no problem for disassembling but putting the pieces together again is big pain HAHA with a torx 6. try to get a torx 5 and emergency room will remain empty  ;D!
Logged
1st: SONY PCM-M10 + DPA 4060's + DPA MPS 6030 power supply (microdot)
2nd: iPhone 5 + "Rode iXY" microphone/"Zoom IQ5" microphone

Offline mmadd29

  • Trade Count: (5)
  • Taperssection Member
  • ***
  • Posts: 581
  • Gender: Male
  • I've stopped drinking, but only while I'm asleep
Re: iRiver 120 torx driver size?
« Reply #4 on: August 14, 2007, 01:32:54 PM »
It was a bitch finding a T5, Home Depot sells a torx screwdriver that is T4 - T10....it's $5
Logged
Superlux CM-H8K > UA5 > iriver h120 > Wave Labs > EAC

Offline SmokinJoe

  • Trade Count: (63)
  • Needs to get out more...
  • *****
  • Posts: 4212
  • Gender: Male
  • "75 and sunny"... life is so much simpler.
    • uploads to archive.org
Re: iRiver 120 torx driver size?
« Reply #5 on: August 15, 2007, 06:14:58 PM »
I got a T5 screwdriver for $2.99 at sears.  +T for the tip.
Logged
Mics: Schoeps MK4 & CMC5's / Gefell M200's & M210's / ADK-TL / DPA4061's
Pres: V3 / ST9100
Decks: Oade Concert Mod R4Pro / R09 / R05
Photo: Nikon D700's, 2.8 Zooms, and Zeiss primes
Playback: Raspberry Pi > Modi2 Uber > Magni2 > HD650
Pages: [1]   Go Up
« previous next »
 

RSS | Mobile
Page created in 0.04 seconds with 29 queries.
© 2002-2025 Taperssection.com
Powered by SMF