Taperssection.com
Gear / Technical Help => Battery Boxes, Preamps, Mixers, ADCs, and Processors => Topic started by: kennedy on July 08, 2004, 01:44:03 AM
-
so ive done a couple stealth recordings, a few times with core sounds stealth mics > d8 and once with my skm140s >mme >d8
the core sounds tapes sucked but very low key and the skm 140 tapes smoked but not very low pro, looking to invest in a pre and ad strictly for stealthin'....... we have a amazing foundation here in slc called GAM they put on a jazz series every winter and this years line up smokes joey defransesco, pat metheny, wynton marsalis, etc. and these all need to get taped :) interested in what are you guys/gals using?
-
An MP2 would fit your needs. I stealth the 140's with it, into an M1, with favorable results.
-
mp2, psp-2, sax are all some small pre's you could easily stealth w/. also have you checked out jk labs stuff?
-
The Aerco MP-2 is built for stealthing! Small black box. No lights. Runs off 3 internal 9V. Sounds great!
-
tonight, i stealthed with this rig: ak40>lc3>km100>mv100>m1. ak40 were mounted in my hat > lc3 > km100 directly into the mv100 > m1. very doable and the results were sweet.
marc
-
I have no problem stealthing w/ my ak40's...I did Dylan AK40">M148>D7 and Bonnie Raitt w/ 40's>MME>D7 both in a very small place. Want smaller....DPA>SX2....psp-2 or 3 are small too.
gfl
jah
-
M1290-HC>MIC 2496> JB3
The MIC 2496 has great LED level meters much easier to see and adjust from, than the JB's meter. Also supplies P48V.
Matt
-
M1290-HC>MIC 2496> JB3
The MIC 2496 has great LED level meters much easier to see and adjust from, than the JB's meter. Also supplies P48V.
Matt
How do you like the sound of it? I also run the micros but through a Shure FP24, which is a very colorful pre.
-
M1290-HC>MIC 2496> JB3
The MIC 2496 has great LED level meters much easier to see and adjust from, than the JB's meter. Also supplies P48V.
Matt
Has you been running it on the 9v battery? Documentation says 1 9V can power 2 48v mics for 4+ hrs., is this accurate?
-
How do you like the sound of it? I also run the micros but through a Shure FP24, which is a very colorful pre.
I’ve done one show with it so far, Aimee Mann a week and a half ago, the tape came out sweet! The best sounding show I’ve taped so far.
Has you been running it on the 9v battery? Documentation says 1 9V can power 2 48v mics for 4+ hrs., is this accurate?
No unfortunately the micros are super power hungry, I made a battery pack to run with it. From my testing I’d say that’s pretty accurate with normal mics. It ran about 50 mins before the low battery LED came on using a nine volt, the low batt light on the ps2 comes on immediately when you plug the mics in.
One note the pre amp is noisier than the ad20 preamp at high levels, if your going to use it for very quiet acoustical music you may want to use something else.
Matt
-
Need to do it more often, but:
AKG 461 -> Aerco -> D8
-
dpa 4061> dpa microdot-to-xlr> lunatec v3> iPaq (pdaudio)
or if I have to go super stealth:
dpa 4061> dpa mps6010 battery box> sony m1 dat
the 4061's are virtually invisible
-
thanks for all the input, +t all around, anyone out there have some mp2 stealth jobs i can listen to
ill b&p or trade for um let me know, heres a link to my list:
www.phishhook.com/lists/ahpagesing
-
I owe ya one JK, so PM me and I'll tell you what I have. 4022 > mp2 > m1 for stealthing.
-
Craig,
just out of curiosity .... how do you stealth a V3 and a 6v batt?
or is that some sort of stealth trade secret? ;)
-
M1290-HC>MIC 2496> JB3
The MIC 2496 has great LED level meters much easier to see and adjust from, than the JB's meter. Also supplies P48V.
Matt
Has you been running it on the 9v battery? Documentation says 1 9V can power 2 48v mics for 4+ hrs., is this accurate?
I can run 2 mics on P48V for 3 hours with just 2 AAs in my pre
-
just out of curiosity .... how do you stealth a V3 and a 6v batt?
Stealthing a V3 and 6v battery is easy if there isn't a heavy pat-down. Pat-down, well...while some people might be able to get away with it, I don't think I'd be able to manage it.
Slim 3-pocket/section fanny pack - SLA in one side pocket, D100 on the other, V3/mic bodies in the middle. No pat-down, no problem.
-
that's what i figured, i guess the question was more directed for heavy pat-down situations.... seems almost impossible by yourself.
thanks
-
M1290-HC>MIC 2496> JB3
The MIC 2496 has great LED level meters much easier to see and adjust from, than the JB's meter. Also supplies P48V.
Matt
Has you been running it on the 9v battery? Documentation says 1 9V can power 2 48v mics for 4+ hrs., is this accurate?
I can run 2 mics on P48V for 3 hours with just 2 AAs in my pre
It's tough to get 2 with the Audix micros with 2 AAs.
-
M1290-HC>MIC 2496> JB3
The MIC 2496 has great LED level meters much easier to see and adjust from, than the JB's meter. Also supplies P48V.
Matt
Has you been running it on the 9v battery? Documentation says 1 9V can power 2 48v mics for 4+ hrs., is this accurate?
I can run 2 mics on P48V for 3 hours with just 2 AAs in my pre
It's tough to get 2 with the Audix micros with 2 AAs.
those things are hogs! I'm using 2200 mAh PowerEXs fwiw
-
M1290-HC>MIC 2496> JB3
The MIC 2496 has great LED level meters much easier to see and adjust from, than the JB's meter. Also supplies P48V.
Matt
Has you been running it on the 9v battery? Documentation says 1 9V can power 2 48v mics for 4+ hrs., is this accurate?
I can run 2 mics on P48V for 3 hours with just 2 AAs in my pre
It's tough to get 2 with the Audix micros with 2 AAs.
those things are hogs! I'm using 2200 mAh PowerEXs fwiw
Tell me about it. I just picked up that walmart batt today. Charged it up and connected for a test, just to see how long it'd last. I'm at 2 1/2 hours and it still shows a full charge. This thing is awesome! ;D
-
M1290-HC>MIC 2496> JB3
The MIC 2496 has great LED level meters much easier to see and adjust from, than the JB's meter. Also supplies P48V.
Matt
Has you been running it on the 9v battery? Documentation says 1 9V can power 2 48v mics for 4+ hrs., is this accurate?
I can run 2 mics on P48V for 3 hours with just 2 AAs in my pre
It's tough to get 2 with the Audix micros with 2 AAs.
those things are hogs! I'm using 2200 mAh PowerEXs fwiw
Tell me about it. I just picked up that walmart batt today. Charged it up and connected for a test, just to see how long it'd last. I'm at 2 1/2 hours and it still shows a full charge. This thing is awesome! ;D
I have a 3000 mAh as well as a 1000 mAh battery pack.
-
AT853s>PS2>AD20>MD
Would like an MP2 if I could ever afford it! ::)
-
AT853s>PS2>AD20>MD
Would like an MP2 if I could ever afford it! ::)
AT853rxwh>mp2>njb3
just posted pics of my minirig in action... The 853 / mp2 combo amazes me...
-
my current stealth rig is 4022 > mp2 > d100, but i've yet to try the combination out. when i had my 140s i ran ak40s > lc3ka > km100 > mp2 > d100 and the combination sounded pretty good when i didn't screw something else up. :) i'll have to admit i don't miss fussing around with the bodies, they were kind of a pain in the ass.
-
4061s > modmps6010 > whatever > d8
-
DPA 4061 > MPS6010 > Oade dual modSBM-1 > M1
DPA 4061 > MPS6010 > Sonosax SX-M2 > modSBM
AT853Rx > Sonosax SX-M2 > modSBM
Oade SBM-1 is mod'd in both the mic and line stages. When I say 'dual mod', I use them both.
Check here if you want to hear it in action....
http://bt.etree.org/?search=dwonk&cat=0
-
AT853Rx/hc/c > mp-2 > neuros
DPA4061 > SP-SPSB-1 > mp-2 > neuros (<------virgin rig)
-
Craig,
just out of curiosity .... how do you stealth a V3 and a 6v batt?
or is that some sort of stealth trade secret? ;)
easiest is the old "false bottom" of my backpack. v3 & battery in the bottom covered with a thin layer of foam and black fabric that matches the backpack lining. Throw a rain jacket or some other b.s. on top. works for light pat downs where they merely look into the bag. just had to do this a few months back for a festival in Philly.
believe it or not, I've crotched one a few times, too. actually it was a v2 back then. baggy pants, lycra shorts.
-
damn, i gotta V2 but it's a 12v :(
i heard if you call grace they will walk you though on how to re-calibrate it to a 6V. i should look into this. wouldn't mind investing in a stealth rig in the future and it would be sweet to use my V2!
thanks
-
M1290-HC>MIC 2496> JB3
The MIC 2496 has great LED level meters much easier to see and adjust from, than the JB's meter. Also supplies P48V.
Matt
Has you been running it on the 9v battery? Documentation says 1 9V can power 2 48v mics for 4+ hrs., is this accurate?
I can run 2 mics on P48V for 3 hours with just 2 AAs in my pre
Hmmm I am getting much better than that (but then again I set the levels, turn the meters off and just watch the NJB3 for levels...) Have a set of rechargeables in it now with over 4 hrs on em and they are still going strong...
-
M1290-HC>MIC 2496> JB3
The MIC 2496 has great LED level meters much easier to see and adjust from, than the JB's meter. Also supplies P48V.
Matt
Has you been running it on the 9v battery? Documentation says 1 9V can power 2 48v mics for 4+ hrs., is this accurate?
I can run 2 mics on P48V for 3 hours with just 2 AAs in my pre
Hmmm I am getting much better than that (but then again I set the levels, turn the meters off and just watch the NJB3 for levels...) Have a set of rechargeables in it now with over 4 hrs on em and they are still going strong...
nice! I'm not saying they won't go longer, just what I have needed to use and been fine with. Gotta use the rechargeables though.
-
M1290-HC>MIC 2496> JB3
The MIC 2496 has great LED level meters much easier to see and adjust from, than the JB's meter. Also supplies P48V.
Matt
Has you been running it on the 9v battery? Documentation says 1 9V can power 2 48v mics for 4+ hrs., is this accurate?
I can run 2 mics on P48V for 3 hours with just 2 AAs in my pre
Hmmm I am getting much better than that (but then again I set the levels, turn the meters off and just watch the NJB3 for levels...) Have a set of rechargeables in it now with over 4 hrs on em and they are still going strong...
nice! I'm not saying they won't go longer, just what I have needed to use and been fine with. Gotta use the rechargeables though.
Yup, as for the MIC 2496 having great meters, nothing beats the meters in a mixpre or mp2, they are even visible in direct sunlight...
-
can any one post some pics of their stealth rig?
Rapahel
-
can any one post some pics of their stealth rig?
Try searching the Rig Pics forum for the keyword "stealth" and you'll find a bunch of pics.
i heard if you call grace they will walk you though on how to re-calibrate it to a 6V.
They have instructions posted on their website in the Support area.
-
Here is my current set up. The only part I do not like is the Hosa XLR to stereo mini cable. I am talking to JKLabs about getting the MPS6010 moded with a permanent pigtail mini (you can't see it, it is in the outside mesh pocket). I use a block of foam between the modSBM and M1 to prevent them from having a frottage session. The REI fanny is really thin, just under 2 inches thick when it is all zipped up....a bit bulkier with all the bits and pieces in there. I can get it around my belly under a slightly baggy tee shirt and sneak it in, but I rarely have to do that. WHen the Sonosax is added to the mix, I wear the modSBM and M1 in the SBM pleather case low near my abdomen....the Sax goes in the REI pack and I got wires going everywhich way between the two.
http://bt.etree.org/?search=dwonk&cat=0 for seeds from this rig!
-
nice stealth sack.....
-
Stealthwise I'm running CS Binaurals>Battery Box>D100.
I'm on my 2nd pair of active cable mics, and have yet to attempt stealthing a show with them. I envy those folks that sneak in Schoeps, Sonosax, MME, and a deck...I can't imagine doing that. Hell, I was nervous enough just throwing a battery box into the mix.
-
can any one post some pics of their stealth rig?
Try searching the Rig Pics forum for the keyword "stealth" and you'll find a bunch of pics.
i heard if you call grace they will walk you though on how to re-calibrate it to a 6V.
They have instructions posted on their website in the Support area.
just saw this brian, thanks! you da man :)
-
Ran my new gear stealth for the first time last week (AT853rx>PS-2>AD-20>JB3). Fairly high security situation (no bags allowed in the venue), which made life a bit tough. Managed to get it all in though. Quite happy with the way things turned out, though the JB3 is hard to read in low light and the AD-20 has no meters. I guess practice will help me in that respect.
Any opinions on the difference in sound quality between the PS-2>AD-20 and the MP-2 w/o A/D converter?
I'll give it another go at the Peter Gabriel show tomorrow methinks.
-
sorry if it's a bit off topic, but I put an mp3 sample of what I taped online and would appreciate any constructive advice that you guys could offer. Overall I'm quite happy with the result but I notice two things that I could improve:
-some noticeable phasing
-some channel inbalance
I guess the phasing might be bacause the mics were on my shirt and maybe too low (I was in the 5th row)? Or maybe I was moving too much?
The channel inbalance is because I was too far stage right. I tried to fix it in Adobe Audition, but maybe could have done a bit more...
Any other advice?
you can download it here: www.unitar.org/ccp/test.mp3
Thanks to all!
-
Or maybe I was moving too much?
you cannot move at ALL when you stealth. the mics must remain stationary.
-
you cannot move at ALL when you stealth. the mics must remain stationary.
It's kinda hard when you're packed into a sold-out venue with people pushing from every direction. I guess I'm used to the omnis I was using before which were a bit more forgiving.
-
sorry if it's a bit off topic, but I put an mp3 sample of what I taped online and would appreciate any constructive advice that you guys could offer. Overall I'm quite happy with the result but I notice two things that I could improve:
-some noticeable phasing
-some channel inbalance
I guess the phasing might be bacause the mics were on my shirt and maybe too low (I was in the 5th row)? Or maybe I was moving too much?
The channel inbalance is because I was too far stage right. I tried to fix it in Adobe Audition, but maybe could have done a bit more...
Any other advice?
you can download it here: www.unitar.org/ccp/test.mp3
Thanks to all!
can can i get this show on cd?
-
Any opinions on the difference in sound quality between the PS-2>AD-20 and the MP-2 w/o A/D converter?
the the AD-Tinny is, well, tinny. And the MP-Bass is bassy
-
you cannot move at ALL when you stealth. the mics must remain stationary.
It's kinda hard when you're packed into a sold-out venue with people pushing from every direction. I guess I'm used to the omnis I was using before which were a bit more forgiving.
That's something you need to take into account when you're getting ready to tape. Make sure you scope out a spot that will sound good and you wont have people pushing from every direction. I've stealthed 2 sold out shows at the 9:30 Club in DC and haven't had a problem with this.
Also, you'll probably want to find a way to rig the mics on your head (i.e. in a hat) rather than on your shirt. You want to get the mics as high as possible when stealthing.
-
setboy, I'll be posting a torrent for it in the "torrents" section today or tomorrow.
-
you cannot move at ALL when you stealth. the mics must remain stationary.
It's kinda hard when you're packed into a sold-out venue with people pushing from every direction. I guess I'm used to the omnis I was using before which were a bit more forgiving.
That's something you need to take into account when you're getting ready to tape. Make sure you scope out a spot that will sound good and you wont have people pushing from every direction. I've stealthed 2 sold out shows at the 9:30 Club in DC and haven't had a problem with this.
Also, you'll probably want to find a way to rig the mics on your head (i.e. in a hat) rather than on your shirt. You want to get the mics as high as possible when stealthing.
yeah, well, it's hard, but it can be done. i do it when i must. i bucked the mosh pit all night tonight - people flying in from the front and sides at static-x in a tiny sold-out club - yet i kept my head from turning. it shifted from side to side with my body (up to a few inches) when i got slammed but that happened only a few times when i just couldn't prevent it. if you brace yourself correctly, you can stand up to some pretty strong attacks... you just have to want it. and then you have a magnificent tape.
true, using omnis in the pit will help if you get run into. if your head turns with directional mics, you're truly fucked. with omnis, you're not so fucked. still fucked, because you can hear it on the tape, but it's not as bad.
anyway, y'all shoulda been there tonight.
armen
-
if your head turns with directional mics, you're truly fucked
Yeah, that was one advantage of running the mics on my shirt rather than my hat, I thought. Freedom to bob my head a bit (almost inevitable at a good show ;D) without impacting the sound. I lose about 8' of mic hight in the process though. Bit of a tradeoff.
-
if your head turns with directional mics, you're truly fucked
Yeah, that was one advantage of running the mics on my shirt rather than my hat, I thought. Freedom to bob my head a bit (almost inevitable at a good show ;D) without impacting the sound. I lose about 8' of mic hight in the process though. Bit of a tradeoff.
a bit of a significant trade off imo....next time your at a show, put your head where the mics would be if they were in your shirt, then listen head level....a huge difference
-
you cannot move at ALL when you stealth. the mics must remain stationary.
It's kinda hard when you're packed into a sold-out venue with people pushing from every direction. I guess I'm used to the omnis I was using before which were a bit more forgiving.
That's something you need to take into account when you're getting ready to tape. Make sure you scope out a spot that will sound good and you wont have people pushing from every direction. I've stealthed 2 sold out shows at the 9:30 Club in DC and haven't had a problem with this.
Also, you'll probably want to find a way to rig the mics on your head (i.e. in a hat) rather than on your shirt. You want to get the mics as high as possible when stealthing.
yeah, well, it's hard, but it can be done. i do it when i must. i bucked the mosh pit all night tonight - people flying in from the front and sides at static-x in a tiny sold-out club - yet i kept my head from turning. it shifted from side to side with my body (up to a few inches) when i got slammed but that happened only a few times when i just couldn't prevent it. if you brace yourself correctly, you can stand up to some pretty strong attacks... you just have to want it. and then you have a magnificent tape.
true, using omnis in the pit will help if you get run into. if your head turns with directional mics, you're truly fucked. with omnis, you're not so fucked. still fucked, because you can hear it on the tape, but it's not as bad.
anyway, y'all shoulda been there tonight.
armen
Haha! Those are the times when you are not only the mic stand, but the shockmounts as well. :)
I have yet to stealth with my AT853 cards, but I have been in those situations with the CSB's.